Effective Sodium Metabisulfite (Na2S2O5), HCl, Sulfur and Distilled Water for the Removal of Pb, Zn and Cr Contaminated Soil in the Columns Method

Abstract

This paper presents an evaluation of different dose of Sodium Metabisulfite (0.01 M Na2S2O5), (Na2S2O5) + (0.1 HCl), and Distilled water for the removal of soil contaminated with Pb, Zn and Cr by the column mode. The field soil contained concentrations of Pb (307.31 mgkg1), Zn (207.77 mgkg1) and Cr (447.50 mgkg1). Both (0.01 M Na2S2O5), (Na2S2O5) + (0.1 HCl), and Distilled water were found to be effective on removing (Na2S2O5) Pb, Cr and Zn respectively. (Na2S2O5) + (0.1 HCl) Cr, Zn and Pb respectively. Sulfur Pb, Cr and Zn respectively. The removal rate of Pb, Zn, and Cr varied from 10.35% - 26%, 3.4% - 21.60% and 4.97% - 23.88% for (0.01 M Na2S2O5 respectively. The removal rate of Pb, Zn, and Cr varied from 16.13% - 20.07%, 8.20% - 23.48%, 5.42% - 28.93% for (0.01 M Na2S2O5 + 0.1 M HCl) respectively. The removal rate of Pb, Zn, and Cr varied from 10.20% - 25.5%, 9.55% - 25.13% and 6.04% - 25.54% for (S) respectively.

Share and Cite:

Salama, A. (2019) Effective Sodium Metabisulfite (Na2S2O5), HCl, Sulfur and Distilled Water for the Removal of Pb, Zn and Cr Contaminated Soil in the Columns Method. Agricultural Sciences, 10, 882-892. doi: 10.4236/as.2019.107067.

1. Introduction

Industrialization and modern lifestyles have led to the production and release of hazardous effluents into the environment [1] [2] . Pollution of soils with nonbiode-gradable pollutants such as heavy metals is an important environmental concern that affects both industrialized and emerging countries [3] [4] [5] [6] . It has been estimated that about 235 million ha of arable land worldwide are polluted by heavy metals [7] . Heavy metals have a considerable toxicity for microorganisms, plants, and animals and can present high potential risks to human health [8] [9] [10] . Many chemical, physical, and biological methods have been suggested to solve the problem of heavy metal contamination, in which soil washing is one of the most effective treatments [11] [12] . Among all heavy metals, lead (Pb) has recently gained increased interest due to its potential to cause various toxicological effects in humans, such as anemia, liver and kidney damage, and cancer [13] . In soil washing techniques, where soil-bound contaminants are transferred to the liquid phase by desorption and solubilization, acid washing and chelator soil washing are two most prevalent removal methods [14] . A mixture of 0.1 M Na2S2O5 and 0.01 M Na2EDTA provide an economically optimum solution for Cd and Zn removal [15] . Soil washing can be practiced in two ways, batch washing and column washing. Compared to batch washing, column washing has many advantages. Firstly, the soil structure remains intact, which is not the case for batch extractions. Secondly, the process can minimize the chance of workers exposure to contaminants [16] . What’s more, column washing was proved to have better metal removal effects than batch washing [17] . Soil washing is particularly frequently used in soil remediation because it: 1) completely removes the contaminants, hence ensures the rapid cleanup of a contaminated site [18] , 2) meets specific criteria, 3) reduces or eliminates long-term liability, 4) may be the most cost-effective solution and may produce recyclable material or energy [19] . Since heavy metals are sparingly soluble and occur predominantly in a sorbed state, washing the soils with water alone is expected to remove too low an amount of cations in the leachates, chemical agents have to be added to the washing water [20] [21] . With chemical soil washing, soil particles are cleaned by selectively transferring the contaminants from the soil into solution [22] . The effectiveness of washing is closely related to the ability of the extracting solution to dissolve the metal contaminants in soils. However, the strong bonds between the soil and metals make the cleaning process difficult. Therefore, only extract ants capable of optimally dissolving the metals must be carefully sought during soil washing. One of the permanent solutions is soil washing with solutions containing chelating agents which, contrary to acid washing processes, permit heavy metal desorption from soil solid phase by forming strong and water soluble metal ligand complexes without deterioration of soil physico-chemical properties [23] . The object of this paper was to evaluate the removal efficiency of the heavy metal by using (0.01 M Na2S2O5), (Na2S2O5) + (0.1 HCl), and S+ Distilled water in treating a contaminated soil in laboratory columns and to select the optimal conditions. The study also focused on the dispose of leaching washing.

2. Materials and Methods

The clay-loam soil used in this study was collected from soil sample surface (0 - 40 cm) located in Bahira City, Egypt northern. The sampling period in (2015), Soil sampling geographic coordinate 31.197045N and 18.098445E. The sample were aired air dried and crushed pass through 2 mm sieve to elaborate the different analysis—Soil Physical Analysis: Texture was determined using sieves and Hydrometer method [24] .

Soil Chemical Analysis: Salinity was measured at in the soil paste extract and pH of 1:2.5 soil suspension by EC meter and PH [25] , Sodium Absorption Ration (SAR) was calculated from Ca, Mg, and Na soluble concentrations, soil organic matter content (OM%) was determined by Walkely & Black method [25] and CaCO3% was determined using the pressure calcimeter method [25] . Table 1 shows chemical characteristics of soil surface sample extremely alkaline, pH values > 8, Nonsaline, moderately sodic and low organic matter.

Columns washing studies were carried in lab to examine the removal efficiency of the heavy-metal by using different includes doses from (0.01 M Na2S2O5), (Na2S2O5) + (0.1 HCl), sulfur and Distilled water in a contaminated soil. Firstly, to evaluate the effect of (0.01 M Na2S2O5), (0.01 Na2S2O5) + (0.1 HCl), Sulfur (250 g) mixture with soil (2250 g) and Distilled water concentrations on the removal of Pb, Zn and Cr. Briefly, 2500 grams of contaminated soil was placed in soil columns (A, B) and 2250 grams of contaminated soil and 250 grams of sulfur of was placed in soil column (C). Distilled water was added to the column (C) samples at 980 ml ratio distilled water. The soils in the columns were initially saturated with deionized water from the bottom to avoid entrapment of air in the soil pore space. Column with 7.5 cm in diameter and 120 cm in height. A plastic mesh (D = 0.2 mm) was placed at the bottom of the column to retain the soil. Due to the long period of time required for leaching of the chelating agent solution from a high-density soil column by gravity and precipitation of some compounds, which decreased hydraulic conductivity of solution during leaching, Determination of metals: heavy metals were determined in soil sample using Atomic Absorption Spectrophotometer Shimadzu model (AA-6650). Digestion of soil sample: Using dry ashing at 430˚C - 600˚C and then diluted with 1:1 (10% HCl: Water) and then filtrate the solution.

3. Results and Discussion

Effects of Na2S2O5 on Heavy Metals Removal:

The evolution of treatment of soil samples with a contamination rate Pb (307.31 mg∙kg−1), Zn (207.77 mg∙kg−1) and Cr (447.50 mg∙kg−1) with heavy metal (Pb, Zn and Cr) Before the Additions of 0.01, Na2S2O5 with corresponding volume

Table 1. Chemical Characteristics of soil surface sample.

of Depths in Table 2. Each for contaminated soil was equal to 980 mL per 2500 g of soil. Remediation of heavy metals contaminated soils depends, among other factors, on the time elapsing between the chelating agent in the leaching solution and the total metal content bound to the soil particles [26] . Meantime, leaching for the first, leaching (Column(A)) by Na2S2O5 at Depth (20 cm) for Pb, Zn and Cr were 54.06 mg∙kg−1, 29 mg∙kg−1, and 60 mg∙kg−1 respectively. at Depth (40 cm) for Pb, Zn and Cr were 31.78 mg∙kg−1, 27.27 mg∙kg−1 and 20 mg∙kg−1 respectively. at Depth (60 cm) for Pb, Zn and Cr were 42.57 mg∙kg−1, 44 mg∙kg−1 and 86 mg∙kg−1 respectively. at Depth (80 cm) for Pb, Zn and Cr were 63.78 mg∙kg−1, 32.53 mg∙kg−1 and 96 mg∙kg−1 respectively. at Depth (100 cm) for Pb, Zn and Cr were 34.97 mg∙kg−1, 36.63 mg∙kg−1 and 50 mg∙kg−1 respectively. at Depth (120 cm) for Pb, Zn and Cr were 26 mg∙kg−1, 33.52 mg∙kg−1 and 90 mg∙kg−1 respectively.

Figure 1 shows the removal efficiency Pb, Zn and Cr in soil after washing with Na2S2O5. The removal rate of Pb, Zn and Cr varied from at Depth (20 cm) for Pb, Zn and Cr were 17.61%, 14.93% and 13.43% respectively. at Depth (40 cm) for Pb, Zn and Cr were 10.35%, 13.45% and 4.97% respectively. at Depth (60 cm) for Pb, Zn and Cr were 13.87%, 21.6% and 21.4%respectively. at Depth (80 cm)

Table 2. Heavy Metals (mg∙kg−1) Content in Sectioned Soil Column Leached with (0.01 M) Na2S2O5.

Figure 1. Effect of concentration on removal of Pb, Zn and Cr from the contaminated soil using (0.01 M Na2S2O5).

for Pb, Zn and Cr were 20.77%, 16.1% and 23.88 %respectively. at Depth (100 cm) for Pb, Zn and Cr were 11.39%, 18% and 12.44% respectively. at Depth (120 cm) for Pb, Zn and Cr were 26.00%, 16.55% and 22.39% respectively. removal efficiencies for Pb, high at Depth (120 cm) concentration obviously affected Pb removal from contaminated soils, removal efficiencies for Cr, at Depth (80 cm), removal efficiencies for Cr, at Depth (120 cm), removal efficiencies for Zn, at Depth (60 cm), removal efficiencies for Zn, at Depth (100 cm), removal efficiencies for pb, at Depth (20 cm). removal efficiencies for Cr and Zn respectively, low at Depth (40 cm), This phenomenon could be explained by that the presence of large concentrations of ions without participation in chelation process (such as the large quantity of sodium ions present in the Na2S2O5 solutions) can lower the stability of metal–chelant complexes [27] . The different properties of the metals and their different release mechanisms resulted in differences in their mobility during soil washing [28] [29] . In the washing process of the column soil, initially, the weakly bound metals were released from the soil, then the residual fractions, strongly bound metals such as oxides and silicates, were extracted from the retained contaminants [30] [31] .

Effects of Na2S2O5 + HCl on Heavy Metals Removal:

The evolution of treatment of soil samples with a contamination rate Pb (307.31 mg∙kg−1), Zn (207.77 mg∙kg−1) and Cr (447.50 mg∙kg−1) with heavy metal (Pb, Zn and Cr) Before the Additions of Na2S2O5+HCl with corresponding volume of Depths in Table 3 Each for contaminated soil was equal to 980 mL per 2500 g of soil. Washing of metal-contaminated soils with 0.1 M HCl, showed some promise as a remediation technique as it rapidly and effectively removes some heavy metals (e.g., Cr, Pb, Zn and Ni) from contaminated soils [32] . Remediation of heavy metals contaminated soils depends, among other factors, on the time elapsing between the chelating agent in the leaching solution and the total metal content bound to the soil particles [26] . Meantime, leaching for the first, leaching (Column (B)) by Na2S2O5 + HCl at Depth (20 cm) for Pb, Zn and

Table 3. Heavy metals (mg∙kg−1) Content in sectioned soil column leached with Na2S2O5 + HCl.

Cr were 45 mg∙kg−1, 23.45 mg∙kg−1 and 6.70 mg∙kg−1 respectively. At Depth (40 cm) for Pb, Zn and Cr were 50 mg∙kg−1, 13.11 mg∙kg−1 and 3.15 mg∙kg−1 respectively. At Depth (60 cm) for Pb, Zn and Cr were 36 mg∙kg−1, 23.62 mg∙kg−1 and 16.78 mg∙kg−1 respectively. At Depth (80 cm) for Pb, Zn and Cr were 56 mg∙kg−1, 37.5 mg∙kg−1 and 12.38 mg∙kg−1 respectively. At Depth (100 cm) for Pb, Zn and Cr were 45 mg∙kg−1, 28.49 mg∙kg−1 and 9.02 mg∙kg−1 ppm respectively. At Depth (120 cm) for Pb, Zn and Cr were 47 mg∙kg−1, 33.54 mg∙kg−1 and 9.97 mg∙kg−1 respectively.

Figure 2 shows the removal efficiency Pb, Zn and Cr in soil after washing with Na2S2O5 + HCl. The removal rate of Pb, Zn and Cr varied from at Depth (20 cm) for Pb, Zn and Cr were 16.13%, 14.68% and 11.54% respectively. at Depth (40 cm) for Pb, Zn and Cr were 17.92%, 8.20% and 5.42% respectively. at Depth (60 cm) for Pb, Zn and Cr were 12.90%, 14.78% and 28.93% respectively. at Depth (80 cm) for Pb, Zn and Cr were 20.07%, 23.48% and 21.34% respectively. at Depth (100 cm) for Pb, Zn and Cr were 16.13%, 17.83% and 15.55% respectively. at Depth (120 cm) for Pb, Zn and Cr were 16.84%, 21% and 17.19% respectively. removal efficiencies for Cr, high at Depth (60 cm) concentration obviously affected Cr removal from contaminated soils, removal efficiencies for Zn, at Depth (80 cm), removal efficiencies for Pb, at Depth (80 cm), removal efficiencies for Pb, at Depth (40 cm), removal efficiencies for Zn, at Depth (100 cm), removal efficiencies for pb, at Depth (20 and 100 cm). removal efficiencies for Zn and Cr respectively, low at Depth (40 cm). 0.1 M hydrochloric acid releases heavy metals from many soil “pools”, e.g., exchangeable, organically complexed and secondary minerals (carbonates, oxides and hydroxides of iron and manganese) [33] . HCl is very effective in the removal of heavy metals and achieve high removal efficiency in the case of natural pH without neutralization to no loss the acidic property that are of high importance for the movement of contaminant sand solubility and thus easily extracted.

Effects of Sulfur 250 g (10%) + Soil 2250 g (90%). Distilled water on Heavy Metals Removal:

The use of elemental S to decrease soil pH and increase the solubility of heavy

Figure 2. Effect of concentration on removal of Pb, Zn and Cr from the contaminated soil using (0.01 M Na2S2O5 + 0.1 HCl).

metals in soils has been suggested [34] [35] [36] . However, more investigations are needed to evaluate the feasibility of this method as a tool for the enhancement of metal solubility and uptake by a metal accumulator in alkaline or neutral soils contaminated by different concentrations of heavy metals. The evolution of treatment of soil samples with a contamination rate Pb (307.31 mg∙kg−1), Zn (207.77 mg∙kg−1) and Cr (447.50 mg∙kg−1) with heavy metal (Pb, Zn and Cr) Before the Additions of Sulfur with corresponding volume of Depths in Table 4 Each for contaminated soil was equal (Distilled water) to 980 mL per 250 g of Sulfur per of 2250 g of soil. Remediation of heavy metals contaminated soils depends, among other factors, on the time elapsing between the chelating agent in the leaching solution and the total metal content bound to the soil particles (26). Meantime, leaching for the first, leaching (Column (C)) by Sulfur at Depth (20 cm) for Pb, Zn and Cr were 7.31 mg∙kg−1, 50 mg∙kg−1 and 5.69 mg∙kg−1 respectively. At Depth (40 cm) for Pb, Zn and Cr were 4.38 mg∙kg−1, 33 mg∙kg−1 and 4.14 mg∙kg−1 respectively. At Depth (60cm) for Pb, Zn and Cr were 4.63 mg∙kg−1, 46 mg∙kg−1 and 2.22 mg∙kg−1 respectively. At Depth (80 cm) for Pb, Zn and Cr were 4.31 mg∙kg−1, 19 mg∙kg−1 and 1.34 mg∙kg−1 respectively. At Depth (100 cm) for Pb, Zn and Cr were 5.06 mg∙kg−1, 21 mg∙kg−1 and 4. 08 mg∙kg−1 respectively. At Depth (120 cm) for Pb, Zn and Cr were 2.92 mg∙kg−1, 30 mg∙kg−1 and 4.80 mg∙kg−1 respectively.

Figure 3 shows the removal efficiency Pb, Zn and Cr in soil after washing with Sulfur 250 g (10%) + Soil 2250 g (90%) with Distilled water. The removal rate of Pb, Zn and Cr varied from at Depth (20 cm) for Pb, Zn and Cr were 25.51%, 25.13% and 25.54% respectively. at Depth (40 cm) for Pb, Zn and Cr were 15.31%, 16.58% and 18.60% respectively. at Depth (60 cm) for Pb, Zn and Cr were 16.18%, 23.12% and 9.97% respectively. at Depth (80 cm) for Pb, Zn and Cr were 15.06%, 9.55% and 6.04 %respectively. at Depth (100 cm) for Pb, Zn and Cr were 17.71%, 10.55% and 18.32% respectively. at Depth (120 cm) for Pb, Zn and Cr were 10.23%, 15.08% and 21.54%respectively. removal efficiencies for Cr,

Table 4. Heavy metals (mg∙kg−1) content in sectioned soil column leached with sulfur 250 g (10%) + Soil 2250 g (90%). Distilled water.

Figure 3. Effect of concentration on removal of Pb, Zn and Cr from the contaminated soil using Sulfur (10%) + Soil (90%) with Distilled water.

high at Depth (20 cm) concentration obviously affected Cr removal from contaminated soils, removal efficiencies for Pb and Zn respectively at Depth (20 cm), removal efficiencies forZn, at Depth (60 cm), removal efficiencies for Cr, at Depth (120 cm), removal efficiencies for Cr, at Depth (60 and 100 cm), removal efficiencies for pb, at Depth (20 cm). removal efficiencies for Cr respectively, low at Depths (60 and 40 cm).

4. Conclusion

The removal efficiencies of Pb, Zn and Cr in the soil by (Na2S2O5), HCl, sulfur and distilled water at different dosages were evaluated. Both Na2S2O5 exhibited good removal efficiencies for extractable Pb in column washing experiment, while Na2S2O5 + HCl and concentrations of were found to be effective in extracting Cr from the contaminated soil tested in the study. But concentrations of the dosage of sulfur did not produce a proportional gain in the Pb, Zn and Cr removing from soils. Sequential extraction indicated that the elements fraction that is weakly bonded to soil particles is insignificant. That is well explained the disproportional gain with the increasing concentration of washing solution. Our study also clearly proved that sequential washing using Na2S2O5 and Na2S2O5 + HCl is likely to be more efficient remediation strategy for the soil than any sulfur and distilled water. This is important, since cost-effectiveness and relatively low environmental impacts are required in the on-site remediation.

Conflicts of Interest

The author declares no conflicts of interest regarding the publication of this paper.

References

[1] Esfandyari, Y., et al. (2015) Degradation and Biodegradability Improvement of the Olive Mill Wastewater by Peroxi-Electrocoagulation/Electrooxidation-Electroflotation Process with Bipolar Aluminum Electrodes. Environmental Science and Pollution Research, 22, 6288-6297.
https://doi.org/10.1007/s11356-014-3832-5
[2] Jaafari, J., Mesdaghinia, A., Nabizadeh, R., Hoseini, M., and Mahvi, A.H. (2014) Influence of Upflow Velocity on Performance and Biofilm Characteristics of Anaerobic Fluidized Bed Reactor (AFBR) in Treating High-Strength Wastewater. J. Environ. Journal of Environmental Health Science and Engineering, 12, 139.
https://doi.org/10.1186/s40201-014-0139-x
[3] Ashrafi, S.D., Rezaei, S., Forootanfar, H., Mahvi, A.H. and Faramarzi, M.A. (2013) The Enzymatic Decolorization and Detoxification of Synthetic Dyes by the Laccase from a Soil-Isolated Ascomycete, Paraconiothyrium variabile. International Biodeterioration & Biodegradation, 85, 173-181.
https://doi.org/10.1016/j.ibiod.2013.07.006
[4] Jafari, J., Mesdaghinia, A., Nabizadeh, R., Farrokhi, M. and Mahvi, A.H. (2013) Investigation of Anaerobic Fluidized Bed Reactor/Aerobic Moving Bed Bio Reactor (AFBR/MMBR) System for Treatment of Currant Wastewater. Iranian Journal of Public Health, 42, 860-867.
[5] Kamani, H., Hoseini, M., Safari, G.H., Jaafari, J. and Mahvi, A.H. (2014) Study of Trace Elements in Wet Atmospheric Precipitation in Tehran, Iran. Environmental Monitoring and Assessment, 186, 5059-5067.
https://doi.org/10.1007/s10661-014-3759-9
[6] Yaghmaeian, K., Jaafarzadeh, N., Nabizadeh, R., Dastforoushan, G. and Jaafari, J. (2015) CFD Modeling of Incinerator to Increase PCBs Removal from Outlet Gas. Journal of Environmental Health Science and Engineering, 13, 60.
https://doi.org/10.1186/s40201-015-0212-0
[7] Bermudez, G., Jasan, R., Plá, R. and Pignata, M.L. (2012) Heavy Metals and Trace Elements in Atmospheric Fall-Out: Their Relationship with Topsoil and Wheat Element Composition. Journal of Hazardous Materials, 213, 447-456.
https://doi.org/10.1016/j.jhazmat.2012.02.023
[8] Ghozikali, M.G., Mosaferi, M., Safari, G.H. and Jaafari, J. (2015) Effect of Exposure to O3, NO2, and SO2 on Chronic Obstructive Pulmonary Disease Hospitalizations in Tabriz, Iran. Environmental Science and Pollution Research, 22, 2817-2823.
https://doi.org/10.1007/s11356-014-3512-5
[9] Kamani, H., Hoseini, M., Seyedsalehi, M., Mahdavi, Y., Jaafari, J. and Safari, G.H. (2014) Concentration and Characterization of Airborne Particles in Tehran’s Subway System. Environmental Science and Pollution Research, 21, 7319-7328.
https://doi.org/10.1007/s11356-014-2659-4
[10] Nouri, J., Mahvi, A. and Bazrafshan, E. (2010) Application of Electro-Coagulation Process in Removal of Zinc and Copper from Aqueous Solutions by Aluminum Electrodes. International Journal of Environmental Science and Technology, 4, 201-208.
[11] Mulligan, C.N. (2005) Environmental Applications for Biosurfactants. Environmental Pollution, 133, 183-198.
https://doi.org/10.1016/j.envpol.2004.06.009
[12] Bolan, N., Kunhikrishnan, A., Thangarajan, R., Kumpiene, J., Park, J., Makino, T., Kirkham, M.B. and Scheckel, K. (2014) Remediation of Heavy Metal(loid)s Contaminated Soils—To Mobilize or to Immobilize? Journal of Hazardous Materials, 266, 141-166.
https://doi.org/10.1016/j.jhazmat.2013.12.018
[13] Hassani, S., et al. (2014) Protective Effects of Curcumin and Vitamin E against Chlorpyrifos-Induced Lung Oxidative Damage. Human & Experimental Toxicology, 34, 668-676.
https://doi.org/10.1177/0960327114550888
[14] Chaiyaraksa, C. and Sriwiriyanuphap, N. (2004) Batch Washing of Cadmium from Soil and Sludge by a Mixture of Na2S2O5 and Na2EDTA. Chemosphere, 56, 1129-1135.
https://doi.org/10.1016/j.chemosphere.2004.03.016
[15] Hauser, L., Tandy, S., Schulin, R. and Nowack, B. (2005) Column Extraction of Heavy Metals from Soils Using the Biodegradable Chelating Agent EDDS. Environmental Science & Technology, 39, 6819-6824.
https://doi.org/10.1021/es050143r
[16] Bassi, R., Prasher, S.O. and Simpson, B.K. (2000) Extraction of Metals from a Contaminated Sandy Soil Using Citric Acid. Environmental Progress, 19, 275-282.
https://doi.org/10.1002/ep.670190415
[17] Neale, C.N., Bricka, R.Y. and Chao, A.C. (1997) Evaluating Acids and Chelating Agents for Removing Heavy Metals from Contaminated Soils. Environmental Progress, 16, 274-280.
https://doi.org/10.1002/ep.3300160416
[18] Wood, P. (1997) Remediation Methods for Contaminated Sites. In: Hester, R. and Harrison, R., (Eds.), Contaminated Land and Its Reclamation, Royal Society of Chemistry, Cambridge.
https://doi.org/10.1680/clair.25950.0003
[19] GOC (2003) Site Remediation Technologies: A Reference Manual. Contaminated Sites Working Group, Ontario.
[20] Davies, A.P. and Singh, I. (1995) Washing of Zinc (II) from Contaminated Soil Column. Journal of Environmental Engineering, 121, 174-185.
https://doi.org/10.1061/(ASCE)0733-9372(1995)121:2(174)
[21] Dikinya, O. and Areola, O. (2010) Comparative Analysis of Heavy Metal Concentration in Secondary Treated Wastewater Irrigated Soils Cultivated by Different Crops. International Journal of Environmental Science and Technology, 7, 337-346.
https://doi.org/10.1007/BF03326143
[22] Nwuche, C.O. and Ugoji, E.O. (2008) Effects of Heavy Metal Pollution on the Soil Microbial Activity. International Journal of Environmental Science and Technology, 5, 409-414.
https://doi.org/10.1007/BF03326036
[23] Xu, Y. and Zhao, D. (2005) Removal of Copper from Contaminated Soil by Use of Poly(amidoamine) Dendrimers. Environmental Science and Technology, 39, 2369-2375.
https://doi.org/10.1021/es040380e
[24] Kettler, T.A., Doran, J.W. and Gilbert, T.L. (2001) Simplified Method for Soil Particle-Size Determination to Accompany Soil-Quality Analyses. Science Society of America Journal, 65, 849-852.
https://doi.org/10.2136/sssaj2001.653849x
[25] Page, A.L., Miller, R.H. and Keeny, R. (1982) Methods of Soil Analysis. Part2. Chemical and Microbiological Properties, Agron. Monograph No. 9, ASA, Madison, WI.
[26] Heil, D., Samani, Z., Hanson, A. and Rudd, B. (1999) Remediation of Lead Contaminated Soil by EDTA. I: Batch and Column Studies. Water, Air, & Soil Pollution, 113, 77-95.
https://doi.org/10.1023/A:1005032504487
[27] Papassiopi, N., Tambouris, S. and Kontopoulos, A. (1999) Removal of Heavy Metals from Calcareous Contaminated Soils by EDTA Leaching. Water, Air, & Soil Pollution, 109, 1-15.
https://doi.org/10.1023/A:1005089515217
[28] Sun, B., Zhao, F., Lombi, E. and McGrath, S. (2001) Leaching of Heavy Metals from Contaminated Soils Using EDTA. Environmental Pollution, 113, 111-120.
https://doi.org/10.1016/S0269-7491(00)00176-7
[29] Zhang, W., Huang, H., Tan, F., Wang, H. and Qiu, R. (2010) Influence of EDTA Washing on the Species and Mobility of Heavy Metals Residual in Soils. Journal of Hazardous Materials, 173, 369-376.
https://doi.org/10.1016/j.jhazmat.2009.08.087
[30] Polettini, A., Pomi, R. and Rolle, E. (2007) The Effect of Operating Variables on Chelant-Assisted Remediation of Contaminated Dredged Sediment. Chemosphere, 66, 866-877.
https://doi.org/10.1016/j.chemosphere.2006.06.023
[31] Tsang, D.C., Zhang, W. and Lo, I. (2007) Copper Extraction Effectiveness and Soil Dissolution Issues of EDTA-Flushing of Artificially Contaminated Soils. Chemosphere, 68, 234-243.
https://doi.org/10.1016/j.chemosphere.2007.01.022
[32] Devis, A.P. and Hotha, B.V. (1998) Journal of Environmental Engineering, 124, 1066.
https://doi.org/10.1061/(ASCE)0733-9372(1998)124:11(1066)
[33] Harmsen, K. (1977) Behaviour of Heavy Metals in Soils. Centre for Agricultural Publishing and Documentation, Wageningen.
[34] Tichy, R., Fajtl, J., Kužel, S. and Kolář, L. (1997) Use of Elemental Sulphur to Enhance a Cadmium Solubilization and Its Vegetative Removal from Contaminated Soil. Nutrient Cycling in Agroecosystems, 46, 249-255.
https://doi.org/10.1007/BF00420560
[35] Seidel, H., Ondruschka, J., Morgenstern, P. and Stottmeister, U. (1998) Bioleaching of Heavy Metals from Contaminated Aquatic Sediments Using Indigenous Sulphur-Oxidizing Bacteria: A Feasibility Study. Water Science & Technology, 37, 387-394.
https://doi.org/10.2166/wst.1998.0776
[36] Kayser, A., Wenger, K., Keller, A., Attinger, W., Felix, H.R., Gupta, S.K., et al. (2000) Enhancement of Phytoextraction of Zn, Cd, and Cu from Calcareous Soil: The Use of NTA and Sulphur Amendments. Environmental Science & Technology, 34, 1778-1783.
https://doi.org/10.1021/es990697s

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.