The Effect of Fabrication Conditions on the Morphology and Photocatalytic Activity of Bismutite Bi2O2CO3 Particles


In this study, three-dimensional bismutite Bi2O2CO3 nanoparticels (BSC NPs) have been synthesized through a facile hydrothermal treatment under mild conditions. The reaction temperatures and NaOH concentration have a vital influence on the physical and photocatalytic properties of the obtained BSC NPs. The crystal structure, morphology, chemical composition, specific surface area and photoresponse of as-obtained catalysts were characterized by X-ray diffraction, Scanning electron microsprctrosopy, Energy-dispersive spectroscopy, N2 adsorption/desorption isotherms and UV-Vis spectra, respectively. Furthermore, Rhodamine 6G was used as model reaction to evaluate the photocatalytic activity of BSC NPs. As a result, there was no obvious effect of hydrothermal reaction temperature and NaOH concentration on phase structure and UV-visible light response; while the morphology, BET surface area and photoactivity were affected by hydrothermal reaction temperature and NaOH concentration.

Share and Cite:

Hu, H. and Xiao, C. (2017) The Effect of Fabrication Conditions on the Morphology and Photocatalytic Activity of Bismutite Bi2O2CO3 Particles. Open Journal of Physical Chemistry, 7, 1-8. doi: 10.4236/ojpc.2017.71001.

1. Introduction

With the increasingly serious environmental problems and dispassion of fossil fuels, the elimination of hazardous chemicals through photochemical degradation technology has attracted enormous research interest [1] . In terms of photo-oxidation approach, it has many unique advantages including mild reaction conditions, low-energy consumption and environmental friendly. However, the photo-oxidation reactions suffer from sluggish kinetics and great energy barrier need to be overcome to achieve a appreciate conversion efficiency.

In recent years, the bismuth-based compounds have attracted much research interest and show excellent performance in a variety of fields such as biomedical fields, solid oxide fuel cells, oxygen sensors, varistors or electrochromic devices as well as environmental science [2] - [8] . Specifically, BSC show significant potential in photocatalysis owing to its excellent photochemical properties according to early reports. For example, Zhang et al. have synthesized 3D BSC nanocrystals for selective adsorption and separation of dyes [9] . Nevertheless, the effect of fabrication conditions of BSC on the photocatalysis performance has been investigated yet [10] . Therefore, the study of fabrication conditions which may have crucial effect on the morphology and photocatalytic properties is necessary [11] .

About 1% - 20% of the total world textile dyes and other industrial dyes are released to waste water [12] . Dye wastewater is typically characterized by strong color, stability and, biotoxicity and carcinogenic effects even at very low concentration, which is harmful to our health and environment [13] [14] . The removal of dyes from waste water has received considerable attention. Compared with traditional physical techniques such as adsorption, ultrafiltration, reverse osmosis and ion exchange that would result in secondary pollution, photocatalytic oxidation can degrade dyes to CO2 and H2O [12] . Rhodamine 6G (R6G) is a typical dye that is chemically stable and poorly biodegradable in waste water. In this paper, we therefore selected R6G as model pollutant to determine the photocatalytic activity. The influence of fabrication conditions on the physical properties and photocatalytic activity of BSC were investigated.

2. Experimental

2.1. Catalyst Preparation

Bismuth nitrate (Bi(NO3)3), urea (CO(NH2)2) and sodium hydroxide (NaOH) were of analytical grade and used without any further purification. Deionized water was used in the whole fabricating process. Three-dimensional bismutite Bi2O2CO3 (BSC) was synthesized by a hydrothermal reaction under mild conditions. 10 mmol of bismuth nitrate and 40 mmol of urea were dissolved in 30 ml of 0.5 - 2 M sodium hydroxide solution. The mud mixture was stirred for 2 h at room temperature with a stirring rate of 600 rpm, and then poured into a Teflon autoclave. The autoclave was put in an oven and allowed to be heated at 120˚C - 160˚C for 6 h under autogenous pressure, and then cooled to room temperature. The precipitates were collected and washed with deionized water and absolute ethanol for 3 times each to remove any residual ions. The final product was dried at 80˚C for 6 - 12 h for further use. The BSC samples synthesized using 0.1 M NaOH and at 120˚C, 140˚C, and 160˚C were noted BSC1, BSC2, BSC3, respectively; and BSC4, BSC5, BSC6 were prepared at hydrothermal temperature of 120˚C using 0.5, 1, 2 M NaOH respectively.

2.2. Characterizations

X-ray diffraction (XRD, D8 ADVANCE) with Cu Kα radiation (25 mA and 40 kV) was used to investigate the structure of the BSC samples. The morphology and composition of the samples were characterized by a scanning electron microscope (SEM, JEOL JSM-7001F) and Energy dispersive spectrometer (EDS) that is attached to JEOL JSM-7001F. UV-Vis absorption spectra of BSC were scanned by a spectrophotometer in the range of 200 - 800 nm (UV-VIS, SHIMADZU UV-2600). The specific surface area, pore size distribution and pore volume were measured by Tristar II3020 and the specific surface area was calculated with the Brunauer-Emmett-Teller (BET) method (Analysis Adsorptive: liquid N2). The adsorbed amount at a P/P0 value of 0.99 was used to estimate the total pore volume. The Barrett-Joyner-Halenda (BJH) method was utilized to calculate the average pore diameter from desorption branch of the isotherm. The as-obtained catalysts were used for photodegradation of R6G and the corresponding photocatalytic activity was investigated by UV-vis spectroscopy.

3. Results and Discussion

3.1. Crystal Structure

Figure 1 shows the X-ray diffraction patterns (XRD) of as-obtained BSC sample synthesized at different conditions. A series of diffraction peaks located at 12.9˚ (002), 23.9˚ (011), 26.03˚ (013), 30.27˚ (110), 32.75˚ (112), 39.48˚ (114), 42.29˚ (020), 47.00˚ (022) and 56.91˚ (123) can be observed, which are ascribed to the tetragonal phase of Bi2O2CO3 (JCPDS: 41-1488). According to the XRD pattern, no obvious alteration and shift can be detected for all 6 BSC samples (BSC1 - BSC6), indicating hydrothermal temperature and the concentration of NaOH have no distinct effects on the structure of BSC.

3.2. Morphologies

Figure 2 shows the morphology of different BSC samples. Similarly, no obvious

Figure 1. XRD patterns of various BSC samples prepared at different conditions.

Figure 2. SEM images of BSC samples at different fabrication conditions.

change can be observed for 6 BSC samples, further illustrating ignorable effect of hydrothermal temperature on the morphology. However, it can be seen that the crystallite size gradually becomes non-uniform with the increase of thermal treatment temperature. As a consequence, the optimal temperature is 120˚C. However, the NaOH concentration shows significant effect on the morphology of the BSC samples. It can be clearly seen that, the BSC particles change into square plates leading to larger sizes with the increase of NaOH concentration. In the hydrothermal reaction, [OH] ions affects the nucleation and growth of oxide crystals. It has been inferred that [OH] ions attach on (110) and (110) facets of oxide crystals, which may hinder the growth of these facets. Therefore, the morphology of BSC crystals gradually changes into square plates. On the other hand, [OH] ions reacts with Bi(NO3)3 to produce Bi(OH)3 or [Bi(OH)4], which are then dehydrated to BiOOH. Meanwhile, NaOH reacts with urea generate sodium carbonate, which speeds up the hydrolysis of urea [9] . Herein, the particle size of BSC becomes larger and even aggregates together with increasing of NaOH concentration. Because the all the as-obtained BSC samples show similar crystal structure, BSC1 was selected as a representative to analyze elemental composition. Figure 3 shows the energy dispersive x-ray spectrum of BSC1, indicating the existence of Bi, C, O elements and among the entire BSC NPs.

3.3. Surface Area and Pore Size Distribution

BET surface area, pore size distribution and pore volume of all as-obtained sample are listed in Table 1. Apparently, the BET surface area and pore volume decrease with the increase of hydrothermal temperature, which is in well agreement with the result observed in SEM images. However, there is no distinct change in BET surface area and pore volume of BSC1 and BSC4 with the change of NaOH concentration (from 0.1 to 0.5 M).

Figure 3. The EDS elemental composition of BSC1.

Table 1. Macroscopic physical properties of BSC.

aVolume of pores between 1.7 nm and 300 nm.

However, the BET surface area decreases sharply when NaOH concentration increases to 1 and 2 M, which attributes to the particle aggregation along with NaOH concentration increasing. This further confirms that NaOH plays dual function. The average pore diameter, calculated by the BJH method based on the desorption branch, shows that the BSC samples have a very clear mesoporous structure with pore size centered at 13.4 and 42.8 nm.

3.4. Photocatalytic Activity

Figure 4 shows UV-Vis diffuse reflectance spectra of different photocatalysts BCS1 - BSC6. The results indicate that different BSC samples have almost same light response.

The photodegration reaction was carried out at room temperature and the pH was adjusted by adding 0.1 M HCl. As reported in our previous work [15] R6G is positively charged in the pH range of below 6.0, BSC surfaces are negatively charged with a zeta potential of about −40 mV. There is bigger binding force between R6G and BSC when the pH is below 6. The results in Figure 5 indicate that all photocatylysts show high photoactivity. However BSC3 and BSC6 have a little lower photoactivity. This is attributed to the low BET surface area of BSC3 and BSC6, which would decrease the contact surface between catalyst and reactant. The photocatalyst reacts with water to form hydroxyl radical (∙OH), which can rapidly attacks pollutants at the surface and in solution as well. Hydroxyl radical (∙OH) is a very powerful oxidant with the oxidation potential of 2.8 V (NHE). Photocatalyst can mineralize organic pollutants into CO2, H2O and so on [16] [17] .

Figure 4. UV-Vis diffuse reflectance spectra of different photocatalysts.

Figure 5. Photodegradation of R6G using different catalysts.

4. Conclusion

Three-dimensional bismutite BSC were prepared through a hydrothermal synthesis with bismuth nitrate, urea and sodium hydroxide under mild conditions. There are no obvious effects of hydrothermal reaction temperature and NaOH concentration on the structure and light response of BSC. However, the particle size, BET surface area, pore volume and photoactivity decrease with the increase of hydrothermal reaction temperature and NaOH concentration. It suggestes that the concentration of NaOH plays dual role in the fabrication of BSC.


Hong Hu is grateful to the Department of Education of Jiangsu Province China for sponsoring her visiting research at Monash University through “Jiangsu Overseas Research & Training Program for University Prominent Young & Middle- aged Teachers and Presidents”.

Conflicts of Interest

The authors declare no conflicts of interest.


[1] Friedmann, D., Mendive, C. and Bahnemann, D. (2010) TiO2 for Water Treatment: Parameters Affecting the Kinetics and Mechanisms of Photocatalysis.Applied Catalysis B-Environmental, 99, 398-406.
[2] Cao, X.F., Zhang, L., Chen, X.T. and Xue, Z.L. (2011) Persimmon-Like (BiO)2CO3 Microstructures: Hydrothermal Preparation, Photocatalytic Properties and Their Conversion into Bi2S3. Cryst Eng Comm, 13, 1939-1945.
[3] Yang, J., Dai, S., Zhou, Y., Wen, L., Hu, L. and Jiang, Z. (2003) Spectroscopic Properties and Thermal Stability of Erbium-Doped Bismuth-Based Glass for Optical Amplifier. Journal of Applied Physics, 93, 977-983.
[4] Dong, F., Ho, W.K., Lee, S.C., Wu, Z., Fu, M., Zou, S. and Huang, Y. (2011) Template-Free Fabrication and Growth Mechanism of Uniform (BiO)2CO3 Hierarchical Hollow Microspheres with Outstanding Photocatalytic Activities under Both UV and Visible Light Irradiation. Journal of Materials Chemistry, 21, 12428-12436.
[5] Zheng, Y., Duan, F., Chen, M. and Xie, Y. (2010) Synthetic Bi2O2CO3 Nanostructures: Novel Photocatalyst with Controlled Special Surface Exposed. Journal of Molecular Catalysis A: Chemical, 317, 34-40.
[6] Briand, G.G. and Burford, N. (1999) Bismuth Compounds and Preparations with Biological or Medicinal Relevance. Chemical Reviews, 99, 2601-2658.
[7] Cheng, G., Yang, H., Rong, K., Lu, Z., Yu, X. and Chen, R. (2010) Shape-Controlled Solvothermal Synthesis of Bismuth Subcarbonate Nanomaterials. Journal of Solid State Chemistry, 183, 1878-1883.
[8] Zhao, T., Zai, J., Xu, M., Zou, Q., Su, Y., Wang, K. and Qian, X. (2011) Hierarchical Bi2O2CO3 Microspheres with Improved Visible-Light-Driven Photocatalytic Activity. Cryst Eng Comm, 13, 4010-4017.
[9] Zhang, X., Zheng, Y., McCulloch, D.G., Yeo, L.Y., Friend, J.R. and MacFarlane, D.R. (2014) Controlled Morphogenesis and Self-Assembly of Bismutite Nanocrystals into Three-Dimensional Nanostructures and Their Applications. Journal of Materials Chemistry A, 2, 2275-2282.
[10] Liu, S., Tu, Y. and Dai, G. (2014) The Effects of Citrate Ion on Morphology and Photocatalytic Activity of Flower-Like Bi2O2CO3. Ceramics International, 40, 2343-2348.
[11] Huang, H., Tian, N., Jin, S., Zhang, Y. and Wang, S. (2014) Syntheses, Characterization and Nonlinear Optical Properties of a Bismuth Subcarbonate Bi2O2CO3. Solid State Sciences, 30, 1-5.
[12] Konstantinou, I.K. and Albanis, T.A. (2004) TiO2-Assisted Photocatalytic Degradation of Azo Dyes in Aqueous Solution: Kinetic and Mechanistic Investigations: A Review. Applied Catalysis B: Environmental, 49, 1-14.
[13] Bao, N., Li, Y., Wei, Z., Yin, G. and Niu, J. (2011) Adsorption of Dyes on Hierarchical Mesoporous TiO2 Fibers and Its Enhanced Photocatalytic Properties. The Journal of Physical Chemistry C, 115, 5708-5719.
[14] Jing, L., Wang, J., Qu, Y. and Luan, Y. (2009) Effects of Surface-Modification with Bi2O3 on the Thermal Stability and Photoinduced Charge Property of Nanocrystalline Anatase TiO2 and Its Enhanced Photocatalytic Activity. Applied Surface Science, 256, 657-663.
[15] Hu, H., Xiao, C., Lin, X., Chen, K., Li, H. and Zhang, X. (2016) Controllable Fabrication of Heterostructured Au/Bi2O3 with Plasmon Effect for Efficient Photodegradation of Rhodamine 6G. Journal of Experimental Nanoscience, 1-12.
[16] Xiao, C., Li, Y., Lu, X. and Zhao, C. (2016) Bifunctional Porous NiFe/NiCo2O4/Ni Foam Electrodes with Triple Hierarchy and Double Synergies for Efficient Whole Cell Water Splitting. Advanced Functional Materials, 26, 3515-3523.
[17] Zhang, X., Yao, J., Ali, M., Wei, J., Wang, H., Yeo, L.Y. Friend, J.R. and MacFarlane, D.R. (2014) UV/Ozone-Assisted Low Temperature Preparation of Mesoporous TiO2 with Tunable Phase Composition and Enhanced Solar Light Photocatalytic Activity. Journal of Materials Chemistry A, 2, 18791-18795.

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.