Effect of Ba Substitution on the Structural and Magnetic Properties of BiFeO3


Bi1-xBaxFeO3 (0 ≤ x ≤ 0.3) nanopowders were synthesized using sol-gel technique. The structural and magnetic properties were investigated using X-ray diffraction, SEM and VSM. As Ba2+ doping concentration was increased, the structure of the samples changed from rhombohedral to tetragonal or monoclinic. The structural change might be an important factor for achieving the ferroelectric properties in this material. The lattice parameters were observed to increase with increase in Ba2+ concentration. All the M-H loops showed the ferromagnetic behavior. Magnetization was observed to enhance with increase in Ba concentration. The enhancement in the magnetization due to Ba2+ doping may be due to the replacement of Bi3+ ions by Ba2+ which might have resulted in the suppression of spiral spin structure.

Share and Cite:

Srinivas, V. , Raghavender, A. and Kumar, K. (2016) Effect of Ba Substitution on the Structural and Magnetic Properties of BiFeO3. World Journal of Nano Science and Engineering, 6, 38-44. doi: 10.4236/wjnse.2016.61004.

Received 28 December 2015; accepted 29 February 2016; published 4 March 2016

1. Introduction

BiFeO3 (BFO) multiferroic materials in nano, bulk and in thin film form have been extensively investigated since the last decade. These materials were successfully used in many technological applications; therefore still lot of research work is going on. BFO is an interesting material due to the co-existence of G-type antiferroicmagnetic (AFM) structure having Néel temperature around 640 K and ferroelectric polarization with Curie temperature around 1000 K [1] [2] . BFO is considered to be superior candidate for the next generation devices such as spintronics, piezoelectric sensors, optoelectroinic devices, non-volatile memories, high density micro actuators etc. [3] [4] . The spontaneous magnetization in BFO could be induced by changing the Fe-O-Fe bond angle or by statistical octahedral distribution of Fe [5] [6] . In BFO, it is believed that, Bi 6s lone pair of electrons is responsible for ferroelectricity while, the partially filled Fe d orbitals lead to magnetic ordering. Room temperature ferromagnetic properties of rare earth, transition metal ions doped BFO materials were observed by several researchers. The enhanced magnetization was observed in BFO due to the divalent, trivalent and rare earth ions on the Fe-site [7] [8] . BFO has rhombohedrally distorted perovskite structure (ABO3) belonging to R3c space group and a complicated spin structure [1] . BFO possess weak ferromagnetic order and ferroelectric polarization. Due to high volatile nature of Bi, oxygen vacancies are produced and due to multiple oxidant states of Fe ions, it causes a high leakage current which degrades ferroelectric properties [9] [10] . The ferromagnetism in BFO is produced due to spin canting which vanishes due to the spiral spin structure of the magnetic domains [9] - [11] . Due to these limitations, pure BFO has very few applications. In order to improve the magnetic and electrical properties of BFO, elements such as Ba2+, Sr2+, Ca2+, La3+, Gd3+, Ti4+, Mn4+, Nb5+ etc., have been substituted in tetrahedral (A) and octahedral (B) sites of pure BFO by which the multiferroic properties were observed to improve.

Ba2+ doping in A site was observed to improve multiferroic properties of BFO. Substituting Ba2+ in BFO distorts its original structure due to larger ionic radii of Ba and changes its cycloidal spin structure to a canted spin structure resulting in the magnetization at room temperature. Also, addition of Ba2+ in BFO is believed to reduce the oxygen vacancy related defects significantly which in turn improves the electrical properties [12] . The synthesis of single phase BFO remains to be challenging task. Several researchers have attempted to prepare BFO using different synthesis techniques and yet the secondary phases are difficult to avoid, but the defects related to the oxygen vacancies have been reduced [13] . In this present work, we intend to investigate and present the results of the structural and magnetic changes taking place with Ba2+ doping in BFO.

2. Experimental

Ba2+ doped BFO was synthesized using sol-gel method [8] [14] [15] . The A.R Grade citric acid (C6H8O7∙H2O), bismuth nitrate (Bi(NO3)3∙5H2O), barium nitrate (Ba(NO3)3∙4H2O), ferric nitrate (Fe(NO3)3∙9H2O) (≥99%) were used as starting materials. The entire synthesis process is described elsewhere [8] [14] [15] . The molar ratio of metal nitrates to citric acid was taken as 1:3. The metal nitrates were dissolved together in a minimum amount of de-ionized water to get a clear solution. An aqueous solution of citric acid was mixed with metal nitrates solution, then ammonia solution was slowly added to adjust the pH at 7. The mixed solution was moved on to a hot plate with continuous stirring at 90˚C. During evaporation, the solution became viscous and finally formed a very viscous brown gel. When finally all remaining water was released from the mixture, the sticky mass began to bubble. After several minutes, the gel automatically ignited and burnt with glowing flints. The decomposition reaction would not stop before the whole citrate complex was consumed. The auto-ignition was completed within a minute, yielding the brown-colored ashes termed as a precursor. The as-prepared powders of all the samples were heat treated separately at 600˚C for 8 h to get the final product.

The X-ray diffraction of the ferrite powders was carried out by using a Philips PW 1820 powder diffractometer with CuKα graphite-monochromated radiation, operating at 40 kV and 30 mA, with solar slits and divergent and receiving slits of 0.2 mm. The diffracted intensity was registered in the angular range 8˚ ≤ 2θ ≤ 80˚, with a step size of 0.02˚ (2θ). The micrographs of all samples were taken on FEI Quanta FEG 200 High Resolution Scanning Electron Microscope. Room temperature magnetic properties were investigated using Lakeshore (USA) VSM 7410.

3. Results and Discussions

Figure 1 shows the X-ray diffraction (XRD) patterns of Bi1−xBaxFeO3 (x = 0.0, 0.1, 0.2, 0.3) measured at room temperature. The XRD peaks show the typical rhombohedral type perovskite structure [16] . Apart from the main BiFeO3 peaks, few minor peaks belonging to Bi2Fe4O9/Bi24Fe2O39/Bi2O3 are also visible. During the synthesis process excess amount of Bi was added in order to avoid non-stoichiometry, therefore the secondary phases seems to appear in the prepared samples. Berbenni et al. [17] showed that, if BFO is annealed at temperatures ≥ 750˚C the secondary phases such as BiO3, Fe2O3, Bi2Fe4O9 will disappears. It seems that higher annealing

Figure 1. X-ray diffraction patterns of Bi1−xBaxFeO3 (x = 0.0, 0.1, 0.2, 0.3).

temperatures increase the intensity of characteristic BFO peaks and reduce the intensity of secondary phases but, may not be possible to avoid the secondary phases. Because, even though the samples were annealed at 800˚C still the traces of the secondary phases are present [17] .

The lattice parameters (a and c) were calculated using the XRD results based on the hexagonal distortion of the rhombohedral unit cell using the following relation and are listed in Table 1.

where d is the inter-planar spacing and (h k l) are the miller indices.

From the Table 1, it is observed that, the lattice parameters increase slightly with increasing Ba doping concentration which is very well in agreement with previously published work on the same materials [18] . With increasing Ba2+ doping content the peak positions shifts slightly towards left indicating the increment in lattice parameters. Since the ionic radii of Ba2+ (2.173 Å) is larger than Bi3+ (1.55 Å), Ba2+ substitution leads to increase in the unit cell volume. The separation between (104) and (110) diffraction peaks are reduced with Ba substitution which may imply that rhombohedral structure might have distorted to either tetragonal or monoclinic structure [19] . These structural changes with Ba2+ doping in BFO might be an important factor considered for ferroelectric properties of these materials.

Figure 2 shows the SEM micrographs for x = 0.0 and 0.2 samples. SEM analysis shows that, the average grain size is around 200 nm. There is no significant change in the grain size with the increase in Ba2+ doping concentration.

Figure 3 shows the hysteresis loops of Bi1−xBaxFeO3 (x = 0.0, 0.1, 0.2, 0.3) samples measured at room temperature with a maximum applied field of 15 kOe. All the samples clearly exhibit a nonlinear magnetization dependence on the magnetic field. The derived parameters from the hysteresis loops such as maximum magnetization (MMax), remnant magnetization (Mr) and coercive field (Hc) are listed in Table 1. Except for x = 0.0, the areas of other loops resembles to square shape rather than the regular S-shape. The loop areas for x = 0.1 and 0.2 are almost similar. But for, higher Ba2+ doping (x = 0.3), the area of the loop appears to be small. The magnetization was observed to enhance with the increase in Ba2+ concentration up to x = 0.2 and with the further increase in x = 0.3, the magnetization is lowered. In our samples, higher Ba2+ doping has resulted for the reduced magnetization. The enhancement of Magnetization with Ba2+ concentration was previously observed [18] [20] [21] . It is observed that, impurity phases in the samples such as Bi24Fe2O39 and BaO do not exhibit room tem-


Figure 2. SEM micrographs of Bi1−xBaxFeO3 (a) x = 0.0 and (b) x = 0.2.

Table 1. Lattice parameters, maximum magnetization, remnant magnetization and coercive filed of Bi1−xBaxFeO3.

Figure 3. Magnetic hysteresis loops of Bi1−xBaxFeO3 samples measured at room temperature.

perature magnetization, therefore the magnetic contribution from those secondary phases can be ruled out [22] [23] .

It is observed that un-doped BFO exhibits ferromagnetic behavior in comparison to the antiferromagnetic nature of the bulk samples [21] . The ferromagnetic behavior of BFO may be due to the modulation of long-range spin cycloidal structure and also due to the antiferromagnetic nature of BFO [21] . In the antiferromagnetic nature of BFO the spin sublattice have ferromagnetic interactions within the sublattice and antiferromagnetic interactions within the sublattice [21] . With the increase of Ba2+ concentration, the grain size did not change significantly, therefore the effect of grain size in our magnetic analysis is not considered.

The enhanced magnetization in our case might be due to suppression of spin spiral structure of BFO and due to the replacement of Bi3+ ions by Ba2+ ions in the lattice site [24] . In which the system will destabilize by creating the charge imbalance. In this process, one oxygen vacancy will be created for every two alkaline metals to stabilize the system [21] [24] . This suppression of spiral spin structure by the oxygen vacancy enhances the ferromagnetism in Ba2+ substituted BFO [24] .

4. Conclusion

Ba2+ doped BFO nanopowders were synthesized using sol-gel method. Lattice parameters were observed to increase with increasing Ba2+ doping concentration. The structure of the samples changed from rhombohedral to tetragonal or monoclinic with Ba2+ doping. The magnetization was observed to enhance with increasing Ba2+ concentration. The enhancement in the magnetization due to the Ba2+ doping may be due to the suppression of spiral spin structure because of the replacement of Bi3+ ions by Ba2+.


KVK is thankful to Dr. N. V. Ramana, Principal, JNTUH CEJ, Nachupally (Kondagattu), Karimnagar-Dist, for his support. Authors sincerely thank the Head and the technical persons of Sophisticated Analytical Instrumentation Facility (SAIF), Indian Institute of Technology (IIT) Madras, India, for providing the VSM and SEM measurements.


*Corresponding author.

Conflicts of Interest

The authors declare no conflicts of interest.


[1] Wang, J., Neaton, J.B., Zheng, H., Nagarajan, V., Ogale, S.B., Liu, B., Viehland, D., Vaithyanathan, V., Schlom, D.G., Waghmare, U.V., Spaldin, N.A., Rabe, K.M., Wuttig, M. and Ramesh, R. (2003) Epitaxial BiFeO3 Multiferroic Thin Film Heterostructures. Science, 299, 1719-1722.
[2] Feng, H.J., Wang, M., Liu, F., Duan, B., Tiam, J. and Guo, X. (2015) Enhanced Optical Properties and the Origin of Carrier Transport in BiFeO3/TiO2 Heterostructures with 109 Domain Walls. Journal of Alloys and Compounds, 628, 311-316. http://dx.doi.org/10.1016/j.jallcom.2014.11.211
[3] Chida, H.U., Veno, R., Funakubu, H. and Koda, S. (2006) Crystal Structure and Ferroelectric Properties of Rare-Earth Substituted BiFeO3 Thin Films. Journal of Applied Physics, 100, Article ID: 014106.
[4] Raghavan, C.M., Kim, J.W. and Kim, S.S. (2014) Effects of Ho and Ti Doping on Structural and Electrical Properties of BiFeO3 Thin Films. Journal of the American Ceramic Society, 97, 235-240.
[5] Kothari, D., Raghavendra Reddy, V., Gupta, A., Phase, D.M., Lakshmi, N., Despande, S.K. and Awasthi, A.M. (2007) Study of the Effect of Mn Doping on the BiFeO3 System. Journal of Physics: Condensed Matter, 19, Article ID: 136202.
[6] Prellier, W., Singh, M.P. and Murugavel, P. (2005) The Single-Phase Multiferroic Oxides: from Bulk to Thin Film. Journal of Physics: Condensed Matter, 17, R803.
[7] Kim, T.Y., Hong, N.H., Sugawara, T., Raghavender, A.T. and Kurisu, M. (2013) Room Temperature Ferromagnetism with Large Magnetic Moment at Low Field in Rare-Earth-Doped BiFeO3 Thin Films. Journal of Physics: Condensed Matter, 25, Article ID: 206003.
[8] Raghavender, A.T. and Hong, N.H. (2011) Effects of Mn Doping on Structural and Magnetic Properties of Multiferroic BiFeO3 Nanograins Made by Sol-Gel Method. Journal of Magnetics, 16, 19-22.
[9] Wang, D.H., Goh, W.C., Ning, M. and Ong, C.K. (2006) Effect of Ba Doping on Magnetic, Ferroelectric, and Magnetoelectric Properties in Mutiferroic BiFeO3BiFeO3 at Room Temperature. Journal of Applied Physics Letters, 88, 1.
[10] Cheng, Z., Wang, X., Dou, S., Kimura, H. and Ozawa, K. (2008) Improved Ferroelectric Properties in Multiferroic BiFeO3 Thin Films through La and Nb Co Doping. Physical Review B, 77, Article ID: 092101.
[11] Ghosh, A.K., Kevin, H., Chatterjee, B., Dwivedi, G.D., Barman, A., Yang, H.D. and Chatterjee, S. (2012) Effect of Sr-Doping on Multiferroic Properties of Bi0.8La0.2Fe0.9Mn0.1O3. Solid State Communications, 152, 557-560.
[12] Makhdoom, A.R., Akhtar, M.J., Rafiq, M.A. and Hassan, M.M. (2012) Investigation of Transport Behavior in Ba Doped BiFeO3. Ceramics International, 38, 3829-3834.
[13] Qi, X., Dho, J., Tomov, R., Blamire, M.G. and MacManus-Driscoll, J.L. (2005) Greatly Reduced Leakage Current and Conduction Mechanism in Aliovalent-Ion-Doped Bi-FeO3. Journal of Applied Physics Letters, 86, Article ID: 062903.
[14] Raghavender, A.T., Pajic, D., Zadro, K., Milekovic, T., Rao, P.V., Jadhav, K.M. and Ravinder, D. (2007) Synthesis and Magnetic Properties of NiFe2-xAlxO4 Nanoparticles. Journal of Magnetism and Magnetic Materials, 316, 1-7.
[15] Raghavender, A.T., Hong, N.H., Park, C., Jung, M.-H., Lee, K.-J. and Lee, D. (2011) Thickness Dependent Magnetic Properties of BiFeO3 Thin Films Prepared by Pulsed Laser Deposition. Materials Letters, 65, 2786-2788.
[16] Rojas-George, G., Concha-Balderrama, A., Silva, J., Fuentes, L. and Reyes-Rojas, A. (2015) Elucidating the Real Effect of Ba and Co Doping on the Magnetic and Optical Properties of BiFeO3. Ceramics International, 41, 9140-9145.
[17] Berbenni, V., Milanese, C., Broni, G., Girella, A. and Marini, A. (2015) Mechanical Activation of the Solid-Phase Reaction between Bismuth Citrate and Iron(II) Oxalate Dihydrate to Yield BiFeO3. Ceramics International, 41, 7216-7220.
[18] El-Desoky, M.M., Ayoua, M.S., Mostafa, M.M. and Ahmed, M.A. (2016) Multiferroic Properties of Nano Structured Barium Doped Bismuth Ferrite. Journal of Magnetism and Magnetic Materials, 404, 68-73.
[19] Das, R. and Mandal, K. (2012) Magnetic, Ferroelectric and Magnetoelectric Properties of Ba-Doped BiFeO3. Journal of Magnetism and Magnetic Materials, 324, 1913-1918.
[20] Mandal, S.K., Rakshit, T., Ray, S.K., Mishra, S.K., Krishna, P.S.R. and Chandra, A. (2013) Nanostructures of Sr2+ Doped BiFeO3 Multifunctional Ceramics with Tunable Photoluminescence and Magnetic Properties. Journal of Physics: Condensed Matter, 25, Article ID: 055303.
[21] Dhir, G., Uniyal, P. and Verma, N.K. (2014) Effect of Particle Size on Multiferroism of Barium-Doped Bismuth Ferrite Nanoparticles. Materials Science in Semiconductor Processing, 27, 611-618.
[22] Qian, F.Z., Jiang, J.S., Guo, S.Z., Jiang, D.M. and Zhang, W.G. (2009) Multiferroic Properties of Bi1-xDyxFeO3 Nano Particles. Journal of Applied Physics, 106, Article ID: 084312.
[23] Pardo, V. and Pickett, W.E. (2008) Magnetism from 2p States in Alkaline Earth Monoxides: Trends with Varying N Impurity Concentration. Physical Review B, 78, Article ID: 134427.
[24] Bhushan, B., Basumallick, A., Bandhopadhyay, S.K., Vasanth Acharya, N.Y. and Das, D. (2009) Effect of Alkaline Earth Metal Doping on Thermal, Optical, Magnetic and Dielectric Properties of BiFeO3 Nanoparticles. Journal of Physics D: Applied Physics, 42, Article ID: 065004.

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.