Experimental Evidence of Capillary Interruption of a Liquid Jet ()

Taha Massalha, Rafael M. Digilov

Academic Arab College for Education, Haifa, Israel.

Department of Education in Technology & Science, Technion-Israel Institute of Technology, Haifa, Israel.

**DOI: **10.4236/ojapps.2014.47037
PDF
HTML
5,587
Downloads
7,043
Views
Citations

Academic Arab College for Education, Haifa, Israel.

Department of Education in Technology & Science, Technion-Israel Institute of Technology, Haifa, Israel.

We observe the gravity discharge of liquid through the short cylindrical tube of diameter of 2 mm and aspect ratio 2.5 and 10 attached to the underside of Mariotte bottle. When the hydrostatic head is reduced and approaches to a certain value, a laminar jet escaped from the nozzle is interrupted and the discharge is drop wise. The plot of the discharge rate as a function of hydrostatic head does not pass through the origin as predicted by Torricelli law for an ideal liquid. We attribute this feature to the energy losses related with creating a new free surface area of the jet. The measurements for water and aqueous ethanol solution are compared with theoretical predictions based on the modified Bernoulli equation with the interfacial energy density correction and good agreement is observed.

Share and Cite:

Massalha, T. and Digilov, R. (2014) Experimental Evidence of Capillary Interruption of a Liquid Jet. *Open Journal of Applied Sciences*, **4**, 392-398. doi: 10.4236/ojapps.2014.47037.

**Keywords:**Mariotte Bottle, Modified Bernoulli Equation, Interfacial Energy Density Correction

1. Introduction

The simplest example of the use of Bernoulli’s equation in introductory physics course [1] is Torricelli’s law, which relates the velocity of efflux of a liquid issuing from the small orifice in a tank to the hydrostatic head of the liquid:

(1)

where is the acceleration due to gravity. This result was recently questioned [2] [3] in the light of experimental evidence that at any nonzero the average discharge velocity is zero. The reason is that Bernoulli’s equation, which is a macroscopic mechanical balance of energy of an ideal, non-viscous liquid, cannot strictly be applied in the case of real flow due to the various dissipation effects [4] [5] , which Equation (1) does not include. Nevertheless, taking into account the energy losses, Bernoulli’s equation was used [3] to modified Equation (1) as follows:

(2)

where and are empirical constants related, respectively, with the losses due to the losses proportional to the fluid velocity squared and the losses independent of the fluid velocity. While the presence of the constant in Equation (2) is somehow justified, there is no physical explanation for the constant. The interpretation proposed in [6] associates with capillary pressure, which hold up the liquid from coming out of the hole.

To give further understanding to this problem, we use the Bernoulli equation modified by the surface energy density and viscosity effect [5] to explain the physical meaning of the correction term. The validity of this approach is demonstrated by measuring the discharge velocity of Newtonian liquids with different surface tension and viscosity using discharge tubes of different aspect ratio.

2. Theoretical Background

Consider a Newtonian liquid of density, viscosity and surface tension discharged under gravity through the short tube of radius and length attached at the side of a large tank. A volume flux from the tube generates the axisymmetrical cylindrical jet of radius. We apply the modified Bernoulli equation [5] with the interfacial energy density along the streamline as is schematically shown in Figure 1:

(3)

where is the mechanical pressure, is the velocity at any point, is the height of the liquid above a reference level, all measured at the same point inside the liquid. The term represents the interfacial energy density required to create a unit of free surface area of the jet, and is the pressure head loss along the streamline due to various dissipative effects.

Let us apply Equation (3) for two points 1 and 2 of Figure 1, i.e. at the free liquid surface in the vessel and inside the jet. Since, , and, we get

(4)

The derivative in Equation (4) consists of two components, one being tangential and the other normal to the jet surface:

Figure 1. Schematic illustration of the discharge of Newtonian liquid from the tank.

(5)

For an ideal cylindrical jet of length, volume and surface area, we have: and, where is due to formation of a fluid-air interface and due to its curvature. The physical meaning of these two effects can be clarified by considering the corresponding values of free energies. Whereas is the interfacial surface energy, the value gives, the excess free energy due to the pressure jump across the interface. These two effects have to be considered together, therefore we have. However, since the shape of the jet is not a perfect cylinder, we introduce in this expression the shape factor to get

(6)

Dissipation term can be expressed [7] -[10] as the sum of the head loss at orifice entry of the tube and losses due to the skin friction within the tube orifice:

(7)

Here, is the coefficient of entry pressure loss, and is the skin friction coefficient, which depends on Reynolds number as

(8)

where and are constants.

Combining Equation (4) with Equations (6) - (8), we obtain the sought equation for the average discharge velocity as a function of the pressure head:

(9)

where constants and are typically, and for laminar flow, and for turbulent flow [10] . For laminar flow, Equation (9) reduces to the quadratic equation for with the solution:

(10)

which involves the effects of viscous resistance and surface tension showing that at the discharge velocity approaches to zero. We refer to this phenomenon as capillary interruption of a liquid jet. When the viscosity term becomes negligible, Equation (10) reduces to Equation (2):

(11)

with. Equations (10) and (11) for the discharge velocity versus the pressure head of real liquids are the main result of present paper.

3. Experiment

To check the validity of the above theoretical approach we quantify the energy losses during the discharge of a real Newtonian fluid from the Mariotte bottle [11] -[13] (see Figure 2). We design a Mariotte bottle from the

Figure 2. Experimental set up for the measuring the discharge rate as a function of the pressure head υ(h).

plastic cylinder of diameter 78 mm and height 40 cm with the opening in the lower part of the wall. Plexiglas’s flange with O-ring at the top of the cylinder provides a seal.

An air intake tube of diameter 8 mm and length 50 cm was inserted through the flange using a compression fitting that seals with an o-ring. Glass capillary tubes with and different lengths were separated inserted in the opening of the cylinder. As a liquid flows out of the bottle it is replaced by air, which enters through the air intake tube and bubbles up through the liquid level to provide a constant flow. The head, equal to the vertical distance from the bottom of the air-inlet tube to the outlet tube, was varied by raising or lowering the inserted tube. The discharge speed of liquid versus the pressure head was determined as follows. The force sensor, connected through a data logger to a computer, continuously recorded the fluid weight escaped from the bottle as a function of time. The average discharge velocity was calculated from the slope as

(12)

Then, using the nonlinear curve fitting procedure available in MATHEMATICA (see Ref. 24 in [5] ), Equation (10) was fitted to measured discharge rate versus the pressure head taking and to be fitting parameters.

4. Results

To clarify the influence of surface tension and viscosity on the discharge rate of real liquids we used ordinary tap water with a density of, viscosity and surface, and also 30% aqueous ethanol of density, viscosity and surface tension. Two tubes of diameter 2 mm and aspect ratio and 10 were separate inserts in the opening of Mariotte bottle. To determine the effusion velocity versus the pressure head, , the liquid of the bottle was poured out into a plastic capacity mounted on the force sensor with the precision of 0.005 N, so that the measurement error over three trial experiments didn’t exceed 1%. Typical results of the discharge rate versus the pressure head are shown in Figure 3 and Figure 4 for two test liquids discharged through

Figure 3. Discharge rate υ versus the pressure head h of tap water. Symbols denote experimental results. Solid lines are predicted by the present theory.

Figure 4. Discharge rate υ versus pressure head h of aqueous ethanol. Symbols denote experimental results. Solid lines are predicted by the present theory.

glass tubes with aspect ration and 10 at temperature. It is seen that the discharge rate strongly depends on the fluid properties and the geometry of the outlet orifice. The range of the average discharge velocity, , Reynolds number, Re and fitting parameters k and b are presented in Table1

As expected, in the case of the discharge through the tube with the viscous resistance plays a prominent role and the rate of discharge as function of the pressure head is better described by Equation (10), whereas Equation (11) provides the best fitting of experimental data of the same liquids discharged

through the orifice with, despite the fact that initially, in the case of water, the Reynolds number was slightly higher than its limit value 3000 for the laminar flow.

It can be seen also from Figure 3 and Figure 4, that over the range of the pressure head under operation, the rate of discharge of both liquids through the orifice with the aspect ratio is considerably less than the rate discharge through the orifice with, as attributed to the viscosity resistance. If the point, at which the rate of the discharge decays to zero, is added to Figure 3 and Figure 4, it can be seen that the fit is quite reasonable. That the plot of in Figure 3 and Figure 4, intersects the horizontal axis at the same point for each liquid independently of the tube aspect ratio, , is indeed related to the fact that fluid flow losses energy in creating the free surface area of the jet as predicted by the theoretical model.

5. Summary

Subject of the discharge of Newtonian liquids from the container through the orifice of small diameter is an interesting topic in science education. One of the most important aspects that students can learn from these studies is the concepts of capillary pressure, interfacial energy and viscous. The use of the modified Bernoulli equation for the liquid jet, involving the interfacial energy density, is very useful for teaching the fundamentals of fluid flow. Students have the opportunity to study the effect of surface tension and viscosity on the fluid flow.

Acknowledgements

This work was partially supported by the Israel Ministry of Absorption and Immigration through the KAMEA Science Foundation.

Conflicts of Interest

The authors declare no conflicts of interest.

[1] | Halliday, D., Resnick, R. and Walker, J. (1977) Fundamentals of Physics Extended. 5th Edition, Wiley, New York. |

[2] |
de Oliveira, P.M.C., Delfino, A., Costa, E.V. and Leite, C.A.F. (2000) Pin-Hole Water Flow from Cylindrical Bottles. Physics Education, 35, 110-119. http://dx.doi.org/10.1088/0031-9120/35/2/306 |

[3] |
Saleta, M.E., Tobia, D. and Salvador, G. (2005) Experimental Study of Bernoulli’s Equation with Losses. American Journal of Physics, 73, 598-602. http://dx.doi.org/10.1119/1.1858486 |

[4] |
Synolakis, C.E. and Badeer, H.S. (1989) On Combining the Bernoulli and Poiseuille Equation—A Plea to Authors of College Physics Texts. American Journal of Physics, 57, 1013-1019. http://dx.doi.org/10.1119/1.15812 |

[5] |
Massalha, T. and Digilov, R.M. (2013) The Shape Function of a Free-Falling Laminar Jet: Making Use of Bernoulli’s Equation. American Journal of Physics, 81, 733-737. http://dx.doi.org/10.1119/1.4819196 |

[6] |
Escamilla, P.L.L. (2009) Surface Tension Influence in Vessel Discharge: Comment on Experimental Study of Bernoulli’s Equation with Losses by Saleta M. E., D. Tobia and G. Salvador Gil [Am J Phys 73 (7), 598-602 (2005)]. American Journal of Physics, 77, 477-478. http://dx.doi.org/10.1119/1.3000362 |

[7] | Fox, R.W. and McDonald, A.T. (1973) Introduction to Fluid Dynamics. Wiley New, York. |

[8] | White, F.M. (1979) Fluid Mechanics. McGraw-Hill, New-York. |

[9] | Streeter, V.L. and Wylie, E.B. (1986) Fluid Mechanics. McGraw-Hill, New-York. |

[10] |
Ramamurthi, K. and Nandakumar, K. (1999) Characteristics of Flow through Small Sharp-Edge Cylindrical Orifices. Flow Measurement and Instrumentation, 10, 133-143. http://dx.doi.org/10.1016/S0955-5986(99)00005-9 |

[11] |
Schwertz, F.A. (1950) Rate-Indicating Mariotte Bottle. Analytical Chemistry, 22, 1214-1216. http://dx.doi.org/10.1021/ac60045a043 |

[12] |
Maroto, J.A. and de Dios, J. (2002) Use of a Mariotte Bottle for the Experimental Study of the Transition from Laminar to Turbulent Flow. American Journal of Physics, 70, 698-701. http://dx.doi.org/10.1119/1.1469038 |

[13] |
Kires, M. (2006) Mariotte Bottle with Side Openings. The Physics Teacher, 44, 388-389. http://dx.doi.org/10.1119/1.2336147 |

Journals Menu

Contact us

+1 323-425-8868 | |

customer@scirp.org | |

+86 18163351462(WhatsApp) | |

1655362766 | |

Paper Publishing WeChat |

Copyright © 2024 by authors and Scientific Research Publishing Inc.

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.