Study on the Effect of Preparation Parameters of K2CO3/Al2O3 Sorbent on CO2 Capture Capacity at Flue Gas Operating Conditions


In this paper, study on the effect of preparation conditions of K2CO3/Al2O3 sorbent was done. Box-Behnken design was applied to study the influence of four parameters involve initial solution concentration, impregnation time and calcination step temperature and time. A quadratic model was used to correlate the sorbent capture capacity. The model was used to calculate the optimum conditions for preparing sorbent. From the analysis of variance (ANOVA), the most influential factor on each experimental design response was identified. The potassium-based sorbents used in this study were prepared by impregnating K2CO3 on Al2O3 support. The CO2 capture capacity was measured in the presence of H2O in a fixed-bed reactor at CO2 capture temperature of 60°C using breakthrough curves. The optimum sorbent prepared by this method showed CO2 capture capacity of 77.21 mg CO2/g sorbent. It was observed that the experimental values obtained were in good agreement with the values predicted by the model, with relatively small errors between the predicted and the actual values. The results obtained in this study can be used as basic data for study on design and operating condition optimization of CO2 capture process using these sorbents.

Share and Cite:

Esmaili, J. and Ehsani, M. (2013) Study on the Effect of Preparation Parameters of K2CO3/Al2O3 Sorbent on CO2 Capture Capacity at Flue Gas Operating Conditions. Journal of Encapsulation and Adsorption Sciences, 3, 57-63. doi: 10.4236/jeas.2013.32007.

Conflicts of Interest

The authors declare no conflicts of interest.


[1] P. Hagewiesche, S. S. Ashour, H. A. Al-Ghawas and O. C. Sandall, “Absorption of Carbon Dioxide into Aqueous Blends of Monoethanolamine and N-Methyldiethanolamine,” Chemical Engineering Science, Vol. 50, No. 7, 1995, pp. 1071-1079. doi:10.1016/0009-2509(94)00489-E
[2] M. Mavroudi, S. P. Kaldis and G. P. Sakellaropoulos, “Reduction of CO2 Emissions by a Membrane Contacting Process,” Fuel, Vol. 82, No. 15-17, 2003, pp. 2153-2159. doi:10.1016/S0016-2361(03)00154-6
[3] R. V. Siriwardane, M. S. Shen, E. P. Fisher and J. A. Poston, “Adsorption of CO2 on Molecular Sieves and Activated Carbon,” Energy & Fuels, Vol. 15, No. 2, 2001, pp. 279-284. doi:10.1021/ef000241s
[4] H. Hayashi, J. Taniuchi, N. Furuyashiki, S. Sugiyama, S. Hirano, N. Shigemoto and T. Nonaka, “Efficient Recovery of Carbon Dioxide from Flue Gases of Coal-Fired Power Plants by Cyclic Fixed-Bed Operations over K2CO3- on-Carbon,” Industrial and Engineering Chemistry Research, Vol. 37, No. 1, 1998, pp. 185-191. doi:10.1021/ie9704455
[5] N. Shigemoto, T. Yanagihara, S. Sugiyama and H. Hayashi, “Material Balance and Energy Consumption for CO2 Recovery from Moist Flue Gas Employing K2CO3-on-Activated Carbon and Its Evaluation for Practical Adaptation,” Energy & Fuels, Vol. 20, No. 2, 2006, pp. 721-726. doi:10.1021/ef058027x
[6] S. C. Lee, B. Y. Choi, S. J. Lee, S. Y. Jung, C. K. Ryu and J. C. Kim, “CO2 Absorption and Regeneration Using Na and K Based Sorbents,” Studies in Surface Science and Catalysis, Vol. 153, No. 1, 2004, pp. 527-530. doi:10.1016/S0167-2991(04)80307-0
[7] S. C. Lee, B. Y. Choi, C. K. Ryu, Y. S. Ahn and J. C. Kim, “Absorption and Regeneration of Alkali Metal-Based Solid Sorbents,” Catalysis Today, Vol. 111, No. 3-4, 2006, pp. 385-390. doi:10.1016/j.cattod.2005.10.051
[8] J. S. Hoffman and H. W. Pennline, “Study of Regenerable Sorbents for CO2 Capture, First National Conference on Carbon Sequestration, Washington,” 2001.
[9] Y. Liang, D. P. Harrison, R. P. Gupta, D. A. Green and W. J. McMichael, “Carbon Dioxide Capture Using Dry Sodium-Based Sorbents,” Energy & Fuels, Vol. 18, No. 2, 2004, pp. 569-575. doi:10.1021/ef030158f
[10] Y. W. Seo, S. H. Jo, C. K. Ryu and C. K. Yi, “Effects of Water Vapor Pretreatment Time and Reaction Temperature on CO2 Capture Characteristics of a Sodium-Based Solid Sorbent in a Bubbling Fluidized-Bed Reactor,” Chemosphere, Vol. 69, No. 5, 2007, pp. 712-718. doi:10.1016/j.chemosphere.2007.05.036
[11] C. Zhao, X. Chen and C. Zhao, “CO2 Absorption Using Dry Potassium-Based Sorbents with Different Supports,” Energy & Fuels, Vol. 23, No. 9, 2009, pp. 4683-4687. doi:10.1021/ef900182d
[12] S. Hirano, N. Shigemoto, S. Yamaha and H. Hayashi, Cyclic Fixed-Bed Operations over K2CO3-on-Carbon for the Recovery of Carbon Dioxide under Moist Conditions,” Bulletin of the Chemical Society of Japan, Vol. 68, No. 3, 1995, pp. 1030-1035. doi:10.1246/bcsj.68.1030
[13] A. G. Okunev, V. E. haronov, Y. I. Aistov and V. N. Parmon, “Sorption of Carbon Dioxide from Wet Gases by K2CO3-in-Porous Matrix: Influence of the Matrix Nature,” Reaction Kinetics and Catalysis Letters, Vol. 71, No. 2, 2000, pp. 355-362. doi:10.1023/A:1010395630719
[14] A. G. Okunev, V. E. Sharonov, A. V. Gubar, I. G. Danilova, E. A. Paukshtis, E. M. Moroz, T. A. Kriger, V. V. Malakhov and Y. I. Aistov, “Sorption of Carbon Dioxide by the Composite Sorbent: Potassium Carbonate in Porous Matrix,” Russian Chemical Bulletin, Vol. 52, No. 2, 2003, pp. 359-363.
[15] I. A. W. Tan, A. L. Ahmad and B. H. Hameed, “Optimization of Preparation Conditions for Activated Carbons from Coconut Husk Using Response Surface Methodology,” Chemical Engineering Journal, Vol. 137, No. 3, 2008, pp. 462-470. doi:10.1016/j.cej.2007.04.031
[16] M. Tir and M. Moulai-Mostefa, “Optimization of Oil Removal from Oily Wastewater by Electrocoagulation Using Response Surface Method,” Journal of Hazardous Materials, Vol. 158, No. 1, 2008, pp. 107-115. doi:10.1016/j.jhazmat.2008.01.051
[17] J. N. Sahu, J. Acharya and B. C. Meikap, “Response Surface Modeling and Optimization of Chromium(VI) Removal from Aqueous Solution Using Tamarind Wood Activated Carbon in Batch Process,” Journal of Hazardous Materials, Vol. 172, No. 2-3, 2009, pp. 818-825. doi:10.1016/j.jhazmat.2009.07.075
[18] A. A. Ahmad, B. H. Hameed and A. L. Ahmad, “Removal of Disperse Dye from Aqueous Solution Using Waste-Derived Activated Carbon: Optimization Study,” Journal of Hazardous Materials, Vol. 170, No. 2-3, 2009, pp. 612-619. doi:10.1016/j.jhazmat.2009.05.021
[19] V. Gunaraj and N. Murugan, “Application of Response Surface Methodologies for Predicting Weld Base Quality in Submerged Arc Welding of Pipes,” Journal of Materials Processing Technology, Vol. 88, No. 1-3, 1999, pp. 266-275. doi:10.1016/S0924-0136(98)00405-1
[20] R. H. Myers and D. C. Montgomery, “Response Surface Methodology: Process and Product Optimization Using Designed Experiments,” John Wiley and Sons, New York, 2002.

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.