Tensile Strength of Squeeze Cast Carbon Fibers Reinforced Al-Si Matrix Composites

Ahmed A. Moosa, Kahtan K. Al-Khazraji, Osama S. Muhammed

Department of Production Engineering and Metallurgy, University of Technology, Baghdad,.
Materials Engineering Department, University of Technology, Baghdad, Iraq..

DOI: 10.4236/jmmce.2011.102009                

Abstract

Squeeze casting is a pressure casting process in which molten metal is solidified under the direct action of a pressure. In squeeze casting, the relationship between the process parameters and the quality of the squeeze cast components is not fully understood; thus the need for more studies in this area of technology for better understanding of the process. The present work encompasses studying the effect of direct squeeze casting process parameters on the production of (3 and 20%) volume fraction carbon fibers (CF) reinforced Al-Si matrix composites. The evaluated process parameters are squeeze pressure in the range (7.5-53) MPa, die preheating temperature (100,200,300)°C, pouring temperature (700,780)°C, squeeze time (30 sec.), and delay time (5 sec.). The results show a good distribution of the matrix between the carbon fibers when using higher casting pressures of (38 and 53MPa), lower pouring temperature of (700°C) and lower die temperatures of (100 and 200°C). Increasing the carbon fibers volume fraction had led to increasing the tensile strength. The using of higher pressure (53MPa), lower pouring temperature (700°C), and lower die temperature (200°C) have increased the ultimate tensile strength of the CF/Al-Si composites to (183MPa) when compared to that of the nonreinforced alloy which was (168MPa) because of the increased bonding, decreased shrinkage defects and fibers degradation based on the results. Also, UTS is increased at P=38MPa, Tp=700°C, and Td=100°C.

Keywords

Tensile Strength , Squeeze Cast Carbon Fibers

Conflicts of Interest

The authors declare no conflicts of interest.

References

[1]	Vijian P., Arunachalam V.P., “Modelling and multi objective optimization of LM24 aluminum alloy squeeze cast process parameters using genetic algorithm” J. Mat. Proc. Tech., vol. 186, 2007, pp. 82-86.
[2]	Dionne S., “Influence of titanium diboride reinforcements on the microstructure, mechanical properties and fracture behavior of cast zincaluminum composites” Ph.D. thesis, department des mines et metallurgie, faculte des sciences et de genie, universite laval, Quebec, CANADA, sept. 1999.
[3]	Dixon Jr. R.G., “Microstructure/property relationships for carbon fiber reinforced aluminum alloys” M.Sc. thesis, Massachusetts Institute of Technology, June 1985.
[4]	Rohatgi P.K., Tiwari V., Gupta N., “Squeeze infiltration processing of nickel coated carbon fiber reinforced Al-2014 composite” J. Mat. Sci., vol. 41, Sept. 2006, pp. 7232- 7239.
[5]	Lancin M., Marhic C., “TEM study of carbon fiber reinforced aluminum matrix composites: influence of brittle phases and interface on mechanical properties” J. European Ceramic Society, vol. 20, Nov. 2000, pp. 1493- 1503.
[6]	He P., Liu Y.Z., Liu D., “Interfacial microstructure and forming mechanism of brazing Cf/Al composite with Al-Si filler” Mat. Sci. Eng., vol. A 422, Feb. 2006, pp. 333-338.
[7]	Daoud A., “Microstructure and tensile properties of 2014 Al alloy reinforced with continuous carbon fibers manufactured by gas pressure infiltration” Mat. Sci. Eng., vol. A391, 2005, pp. 114-120.
[8]	Levitt A.P., Band H.E., “Method of making metal impregnated graphite fibers” US Patent, no. 4157409, Jun./5/1979.
[9]	Donomoto T., Tanaka A., Tatematsu Y., Akai T., “Fiber reinforced metal type composite material with high purity aluminum alloy containing magnesium as matrix metal” US Patent, no. 4450207, May/22/1984.
[10]	Divecha A.P., Karmarkar S.d., “process for producing graphite fiber/aluminummagnesium matrix composites” US Patent, no. 4578287, Mar./25/1986.
[11]	Kyono T., Ohnishi S., Hanano T., Hotta T., “Preform wire for a carbon fiber reinforced aluminum composite material and a method of manufacturing the same” US Patent, no. 208039, May/29/1990.
[12]	Hufnagel W., “Key to Aluminum alloys” Aluminum-Verlag, Düsseldorf, 1982, p. 119.
[13]	Maleki A., Niroumand B., Shafyei A., “Effects of squeeze casting parameters on density, macrostructure and hardness of LM13 alloy” Mat. Sci. Eng., vol. A428, 2006, pp. 135-140.
[14]	Takhakh A.M., “Solidification simulation and experimental investigation of Al-Si cast structures” Ph.D. thesis, Department of Production Engineering and Metallurgy, University of Technology, Baghdad, Iraq, 2007.
[15]	Schwam D., Wallace J.F., Chang Q., Zhu Y., “Optimization of the squeeze casting process for aluminum alloy parts” final report, Case Western Reserve University, OH, USA, July 2002.
[16]	Meyers M.A., Chawla K.K., “Mechanical behavior of materials” Prentice- Hall, Inc., USA, 1999, p. 644.
[17]	Jayamathy M., et.al., “Influence of reinforcement on microstructure and mechanical response of a magnesium alloy” Current Science, vol. 87, no. 9, nov. 2004, pp. 1218- 1231.
[18]	Li S.H., Chao C.G., “Effects of carbon fiber/Al interface on mechanical properties of carbon-fiber-reinforced aluminum-matrix composites” Met. & Mat. Trans. A, vol. 35A, July 2004, pp. 2153-2160.
[19]	Ryu Y.M., Yoon E.P., Rhee M.H., “NCG reinforced MMC fabricated by the squeeze casting method” App. Comp. Mat., vol. 7, 2000, pp. 251-267.
[20]	Raji A., Khan R.H., “Effects of pouring temperature and squeeze pressure on Al-8 % Si alloy squeeze cast parts” AU J. T., vol. 9, no. 4, April 2006, pp. 229-237.
[21]	Yong M.S., Clegg A.J., “Process optimization for a squeeze cast magnesium alloy metal matrix composite” J. Mat. Proc. Tech., vol. 168, 2005, pp. 262-269.
[22]	Yue T.M., “Squeeze casting of high-strength aluminum wrought alloy AA7010” J. Mat. Proc. Tech., vol. 66, 1997, pp. 179-185.
[23]	Baron R.P., Wert J.A., Gerard D.A., Wawner F.E., “The processing and characterization of sintered metal-reinforced aluminum matrix composites” J. Mat. Sci, vol. 32, 1997, pp. 6435-6445.
[24]	Dieter G.E., “Mechanical Metallurgy” McGraw-Hill, Inc, USA, Second Edition, 1976, p. 258.
[25]	ASM Metals Handbook, “casting”, 9th edition, 4th printing, vol. 15, Materials park, OH, 1998.