Studies on Aluminum-Iron Ore in-Situ Particulate Composite
S. Sarkar, Akhilesh Singh
DOI: 10.4236/ojcm.2012.21004   PDF    HTML     6,262 Downloads   12,571 Views   Citations


Discontinuously reinforced aluminium matrix composites are fast emerging as engineering materials and competing with common metals and alloys. They are gaining significant acceptance because of higher specific strength, specific modulus and good wear resistance as compared to ordinary unreinforced alloys. Reinforcing particles or short fibers normally used are silicon carbide and alumina which are added externally. Recently it has been shown that alumina particles can be produced in-situ by reaction with metallic oxides reduced by aluminium. Alumina particles thus produced are dispersed in the aluminium matrix and the elementary metal gives solid solution strengthening of the matrix. In-situ particulate composites in comparison with conventional cast particulate composites produced by external addition promote cleaner interface, eliminates interface incompatibility of the matrices with the reinforcements, help to achieve greater thermodynamic stability of reinforcement particles in the matrix at elevated temperature and also increase the possibility of developing coherency between the matrix and particles formed in-situ. The morphology and the distribution of particles strongly influence the physical and mechanical properties of composites. In the present investigation, iron ore was added to molten aluminium, aluminium-magnesium and aluminium-silicon alloys by vortex method. The iron oxides present in the iron ore are observed to react with aluminium, magnesium resulting in production of Al2O3, MgO and metallic iron which dissolved in liquid aluminium. The composites thus produced were cast into cast iron die. The mechanical properties of the composites were evaluated. The dry sliding wear behavior of the cast composites was studied at different loads and different sliding velocities using Pin-On-Disk configuration wear testing machine. The worn surfaces and the wear debris were also analyzed using optical microscope and scanning electron microscope.

Share and Cite:

S. Sarkar and A. Singh, "Studies on Aluminum-Iron Ore in-Situ Particulate Composite," Open Journal of Composite Materials, Vol. 2 No. 1, 2012, pp. 22-30. doi: 10.4236/ojcm.2012.21004.

Conflicts of Interest

The authors declare no conflicts of interest.


[1] I. A. Ibrahim, F.A. Mohamed, E.J. Lavernia, “Metal Matrix Composites—A Review,” Journal of Material Science, Vol. 26, No. 5, 1991, pp. 1137-1157. doi:10.1007/BF00544448
[2] S. Basavarajappa, G. Chandramohan, A. Mahadevan, M. Thangavelu, R. Subramanian and P. Gopalakrishnan, “Influence of Sliding Speed on the Dry Sliding Wear Behaviour and the Subsurface Deformation on Hybrid Metal Matrix Composite,” Wear, Vol. 262, No. 7-8, 2007, pp. 1007-1012. doi:10.1016/j.wear.2006.10.016
[3] I. Sinclair and P. J. Gregson, “Structural Performance of Discontinuous Metal Matrix Composites,” Material Science Technology, Vol. 13, No. 9, 1997, pp. 709-725.
[4] A. P. Sannino and H. J. Rack, “Dry Sliding Wear of Discontinuously Reinforced Aluminium Composites: Review and Discussion,” Wear, Vol. 189, No. 1-2, 1995, pp. 1- 19. doi:10.1016/0043-1648(95)06657-8
[5] B. C. Pai, T. P. D. Rajan and R. M. Pillai, “Aluminium Matrix Composite Castings for Automotive Applications,” Indian Foundry Journal, Vol. 50, 2004, pp. 30-39.
[6] M. K. Surappa, “Aluminium Matrix Composites: Challenges and Opportunities,” Sadhana, Vol. 28, No. 1-2, 2003, pp. 319-334. doi:10.1007/BF02717141
[7] K. G. Satyanarayana, R. M. Pillai and B. C. Pai, “Recent Developments and Prospects in Cast Aluminium Matrix Composites,” Transactions of the Indian Institute of Metals, Vol. 55, No. 3, 2002, pp. 115-130.
[8] F. Gul and M. Acilar, “Effect of the Reinforcement Volume Fraction on the Dry Sliding Wear Behaviour of Al-10Si/SiCp Composites Produced by Vacuum Infiltration Technique,” Composites Science and Technology, Vol. l64, No. 13-14, 2004, pp. 1959-1970.
[9] S. F. Corbin and D. S. Wilkinson, “The Influence of Particle Distribution on the Mechanical Response of a Particulate Metal Matrix Composite,” Acta Metallurgica et Materialia, Vol. 42, No. 4, 1994, pp. 1311-1318. doi:10.1016/0956-7151(94)90147-3
[10] S. Sarkar, S. Tripathy and S. Mohan, “Effect of Si and Mg Addition on Dry Sliding Wear of Al-Fly Ash Metal Matrix Composite,” Journal of Composite Materials, Vol. 9, No. 49, 2009, pp. 1-17.
[11] S. B. Prabu, L. Karunamoorthy, S. Kathiresan and B. Mohan, “Influence of Stirring Speed and Stirring Time on Distribution of Particles in Cast Metal Matrix Composite,” Journal of Materials Processing Technology, Vol. 171, No. 20, 2006, pp. 268-273. doi:10.1016/j.jmatprotec.2005.06.071
[12] N. chawla and Y.-L. Shen, “Mechanical Behavior of Particle Reinforced Metal Matrix Composites,” Advanced Engineering Materials, Vol. 3, No. 6, 2001, pp. 357-370. doi:10.1002/1527-2648(200106)3:6<357::AID-ADEM357>3.0.CO;2-I
[13] S. M. L. Nai and M. Gupta, “Influence of Stirring Speed on the Synthesis of Al/Sic Based Functionally Gradient Materials,” Composite Structures, Vol. 57, No. 1-4, 2002, pp. 227-233. doi:10.1016/S0263-8223(02)00089-2
[14] J. Hashim, L. Looney and M. S. J. Hashmi, “Metal Matrix Composites: Production by the Stir Casting Method,” Journal of Materials Processing Technology, Vol. 92-93, 1999, pp. 1-7. doi:10.1016/S0924-0136(99)00118-1
[15] P. K. Ghosh and S. Ray, “Fabrication and Properties of Compocast Aluminium-Alumina Particulate Composites,” Indian Journal of Technology, Vol. 26, 1988, pp. 83-94.
[16] D. J. Lloyd, “Particle Reinforced Aluminium and Magnesium Matrix Composites,” International Materials Reviews, Vol. 39, No. 1, 1994, pp. 1-23
[17] N. Aniban, R. M. Pillai and B. C. Pai, “An Analysis of Impeller Parameters for Aluminium Metal Matrix Composites Synthesis,” Materials and Design, Vol. 23, No. 6, 2002, pp. 553-556. doi:10.1016/S0261-3069(02)00024-9
[18] R. M. Aikin Jr., “The Mechanical Properties of in-Situ Composites,” JOM Journal of the Minerals, Metals and Materials Society, Vol. 49, No. 8, 1997, pp. 35-39. doi:10.1007/BF02914400

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.