Modeling and Numerical Simulation of Material Science

Modeling and Numerical Simulation of Material Science

ISSN Print: 2164-5345
ISSN Online: 2164-5353
www.scirp.org/journal/mnsms
E-mail: mnsms@scirp.org
"Finite Element Analysis of the Groove Pressing of Aluminum Alloy"
written by Mehdi Shaban Ghazani, Akbar Vajd,
published by Modeling and Numerical Simulation of Material Science, Vol.4 No.1, 2014
has been cited by the following article(s):
  • Google Scholar
  • CrossRef
[1] Bending Forces and Hardness Properties of Ti6Al4V Alloy Processed by Constrained Bending and Straightening Severe Plastic Deformation
2020
[2] Experimental and Numerical Investigation of Mechanical Properties in the Ultrasonic Assisted constraint groove pressing process of copper sheets
2020
[3] Prabhat Chand Yadav, Arush Sinhal, Sandeep Sahu, Abir Roy & Shashank Shekhar
2020
[4] CHARACTERISATION OF TITANIUM ALLOY PROCESSED BY CONSTRAINED BENDING AND STRAIGHTENING SEVERE PLASTIC DEFORMATION
2020
[5] SIMULACIÓN DE LA DEFORMACIÓN PLÁSTICA POR CORRUGACIÓN-ESTIRAMIENTO DEL TITANIO GRADO 2
2019
[6] Effect of Coating Process Parameters on the Development of Residual Stresses in Ceramic Coatings
2019
[7] Influence of Precipitation and Dislocation Density on Flow Stress Characteristics Under Compression Deformation of Heat-Treated 17-4 PH Stainless Steel Alloy
2019
[8] Numerical Investigation on Strain Properties of Ti6Al4V Alloy Processed by Constrained Bending and Straightening Severe Plastic Deformation
2019
[9] Experimental and Numerical Study of Severe Plastic Deformation in the Constrained Groove Pressing Process on the Pure Copper Sheets
2019
[10] High toughness magnesium alloy through severe plastic deformation and short annealing
2018
[11] Experimental Investigation of Mechanical Behavior of a Polyamide before and after Constrained Groove Pressing Process
International Journal of Engineering Research in Africa, 2018
[12] Performance and Prospects of Severe Plastic Deformation for Effective Biomedical Titanium Alloys
2018
[13] Finite element analysis of the deformation behaviour of pure aluminium in repetitive corrugation-straightening and constrained groove pressing
International Journal of Manufacturing Technology and Management, 2018
[14] Journal of Modern Materials
2018
[15] Simulation studies on RCS processed Al-Mg-Sc alloy
2018
[16] ELEMENTOS FINITOS DE LA DEFORMACIÓN PLÁSTICA SEVERA EN LÁMINAS DE TITANIO
2017
[17] EŞİT KANALLI AÇISAL PRESLEME YÖNTEMİNİN İNCELENMESİ VE 6063 ALÜMİNYUM ALAŞIMINA UYGULANMAS
2017
[18] Modeling of bake-hardening effect for fine grain bainite-aided dual phase steel
Materials & Design, 2017
[19] Microstructure, hardness homogeneity, and tensile properties of 1050 aluminum processed by constrained groove pressing
Applied Physics A, 2017
[20] Finite Element Analysis of ECAP, TCAP, RUE and CGP Processes
IOP Conference Series: Materials Science and Engineering, 2016
[21] Microstructural Inhomogeneity in Constrained Groove Pressed Cu-Zn Alloy Sheet
Journal of Materials Engineering and Performance, 2016
[22] Effect of Fine Grained Dual Phase Steel on Bake Hardening Properties
steel research international, 2016
[23] Constrained groove pressing for sheet metal processing
Progress in Materials Science, 2016
[24] The Study of the Behavior of Constrained Groove Pressed Magnesium Alloy after Heat Treatment
Acta Physica Polonica, A., 2015
[25] Finite element analysis of medium-wheel Bulldozer earth-moving shovel arm based on ANSYS
2014
Free SCIRP Newsletters
Copyright © 2006-2021 Scientific Research Publishing Inc. All Rights Reserved.
Top