Consideration of Size and Dimension in the Evaluation of Transfers during Convective Drying of Sweet Potato ()
1. Introduction
The heat and mass transfer in biological structure is dictated by several parameters [1] [2] [3]. Several studies have highlighted the influences of environmental parameters such as temperature [4] [5], velocity [2], relative humidity [6] [7] of the air [8] [9] [10]. In addition to these parameters, there are also parameters related to the nature of the matter [11] [12]. Ouoba [13] has established that the internal structure of the product varies during drying and leads to changes in the behavior of the material regarding heat and masse transfers [8] [14] [15]. Ouoba et al. [16] have shown that the intrinsic properties of the product play a role on the quality of transfers during convective drying, using okra as a product with a complex macrostructure and also potato considered as a product with a homogeneous structure. Ganame et al. [17] took the study further by using several products such as tomato, cucumber, zucchini and came to the same conclusion that the structure of the product dictates the law of transfers during its convective drying. Using samples of potatoes of various shapes and sizes, Ouoba et al. [13] [18] concluded that it is not possible to characterize the drying of a product without taking into account its shape and size. Ouoba [13] introduces the notion of characteristic dimension to bypass the notion of shape when evaluating the convective drying of agrifood products.
In this present work, we will look for the importance of taking into account the size and the initial shape of cubic, cylindrical and spherical sweet potato samples. We will particularly examine the contribution of the form factor defined by Ouoba [13] for these different samples, during their convective drying.
2. Material and Methods
2.1. Sweet Potato
In order to follow the evolution of the water content of the product, with regard to its size and shape, it is essential to take a product with a quasi-uniform macro-structure and which lends itself easily to cutting. Sweet potato is a product that has these criteria. In addition, we can easily cut fairly large samples from sweet potato, which may go to the size useful for our experiments.
Sweet potato was purchased at a local fruit market in Bobo-Dioulasso, Burkina Faso and transported to the laboratory. They were kept under slightly damp sand. This is the traditional method of preserving sweet potatoes in Burkina Faso. This method allows keeping the tuber fresh for a long period of time, up to more than 03 months. They are dug up washed, peeled and cut to the desired shape and size. For this present work, we kept the cubic, spherical and cylindrical shapes. The [WTF BINDER] oven is first set to a temperature of 80˚C. A balance [STRASTON ± 0.001 g] is used to determine the mass of the samples. To establish the drying kinetics, the sample is removed from the oven at a fixed time interval, after a first rough test, its mass is measured and it is reintroduced into the oven. The measurement time is minimized [2] [13] so as not to disturb the mass and heat transfer processes already established in the sample [16].
The samples, once cut, are kept in a container filled with water; this is to avoid the establishment of transfers before their introduction into the dryer.
When thermal equilibrium is reached in the oven, the samples are removed from the water and then wiped using a blotting paper [2] [13] [19]. Thus, the residual water kept on the surface is eliminated.
They are therefore introduced into the oven where drying begins, just after having noted their respective mass.
2.2. Experiment Process
During the drying experiment, some precautions are taken in order to minimize the contribution of the other parameters on the evaluation of the importance of the size on the drying [20] [21] [22].
The study’s opening time is as short as possible. It is in view of not disturbing too much the thermal balance pre-established within it [11] [18].
The time taken to collect the masses is reduced as much as possible. This is in order not to disturb the thermal equilibrium established in the materials [2] [17].
Samples are removed from the oven at pre-set time intervals. They are weighed for the determination of the mass at the instant t of drying,
.
2.3. Data Processing
The initial water content
of sweet potato is determined by taking the initial mass
of the sample. Then, the sample is introduced in an oven set at 70˚C for 24 hours. The mass of the sample after the 24 hour stay is the mass of the solid skeleton, i.e. the mass of the sample without any trace of water. We will denote it
. The initial water content is calculated by the following relation [3] [13] [23]:
(1)
Establishing drying kinetics requires collecting the mass of the sample over time. At a given time t from the mass
of the sample, we deduce the water content
of the sample by the relation [11] [13]:
(2)
Then, we get the kinetics curve by plotting the relation
3. Results and Discussions
3.1. Taking into Account the Size
3.1.1. Cubes of Edges 1, 2, 3 and 4 cm
Figure 1 compares the behavior of cubic samples of different dimensions, i.e. edges of 1, 2, 3, and 4 cm, subjected to convective drying at 80˚C.
For this cubic shape, the results show that size plays an important role in the process of water transfer into the product.
From the first 50 minutes, the small sample, i.e. the sample at 1 cm edge, is already at 50% of its initial water content. For the same duration, the largest sample, the sample at 4 cm edge is about 90% of its initial water content. The 2 cm and 3 cm edges of cubic samples are, respectively, at 65% and 80% of their initial water content.
At 250 min of drying time, the cube at 1 cm edge is almost dry. The large sample only lost half of its water content. The samples at 2 cm and 3 cm edges are at about 20% and 40% of their initial water content during this drying period, i.e. 250 min.
These results reveal the importance of taking into account parameters such as dimension during the drying process of agro-food products, as suggested by Ouoba [19].
Figure 1. Influence of the initial dimension on convective drying, T = 80˚C, cubes of sweet potatoes
It would therefore be advisable, for a dried product of uniform quality, to separate the cubic samples according to their sizes before their convective drying.
3.1.2. Spheres, Diameters 1, 2, 3 and 4 cm
Figure 2 compares the behavior of spherical samples of different sizes, under convective drying at 80˚C. The spherical shaped samples used for this present case have diameters of 1, 2, 3 and 4 cm.
For this spherical shape, the efficiency of the transfers is directly linked to the initial size of the sample.
From the first 50 minutes, the small sample, i.e. the 1 cm diameter sample is already at 55% of its initial water content. Meanwhile, the larger sample, the 4 cm diameter sample is about 85% of its original water content. spherical samples of 2 cm and 3 cm in diameter are, respectively, at 80% and 78% of their initial water content.
After a drying time of 280 min, the 1 cm diameter sphere has reached its final water content. The large sample lost only 55% of its water content. The samples 2 cm and 3 cm in diameter are approximately 28% and 40% of their initial water content during this drying period, i.e. 280 min.
For the spherical shape, the analysis of the results therefore proves that the initial dimension is an important parameter for the evaluation of the drying of sweet potato.
Optimizing the drying of cubic shapes requires separating or sorting the samples according to their initial size, if they have the spherical shape
3.1.3. Cylinders Hxd: 1 × 1, 2 × 2, 3 × 3 et 4 × 4 cm
Figure 3 compares the behavior of cylindrical samples of different dimensions, subjected to convective drying at 80˚C.
The samples used have a height-diameter dimension of 1 cm × 1 cm, 2 cm × 2 cm, 3 cm × 3 cm and 4 cm × 4 cm. For this cylindrical shape, the results show that the dimension plays an important role in the process of water transfer into the product.
Figure 2. Influence of the initial dimension on convective drying, T = 80˚C, sweet potato spheres.
Figure 3. Influence of the initial dimension on convective drying, T = 80˚C, cylinders of sweet potatoes.
The small sample, i.e. height-diameter of 1 cm × 1 cm, reached half of its initial water content in about the first 50 minutes.
For the same time, the larger sample, the 4 cm × 4 cm height-diameter sample is about 88% of its initial water content. Cylindrical samples of 2 cm × 2 cm and 3 cm × 3 cm height-diameter are, respectively, 70% and 80% of their initial water content.
At 260 min of drying time, the 1 cm × 1 cm height-diameter cylinder is almost dry. The large sample only lost half of its water content. The samples at 2 cm × 2 cm and 3 cm × 3 cm height-diameter are at approximately 20% and 40% of their initial water content during this drying period, i.e. 260 min.
These results show the importance of taking into account parameters such as size during the drying process of agro-food products.
It would therefore be, for a dry product of good quality, to separate the cylindrical samples according to their size before their convective drying.
3.2. Taking into Account the Shape
While it is established from the above that size is an important parameter in the appreciation of drying, it is also important to examine the role that shape plays in this process of drying agrifood products.
At the drying temperature of 80˚C, we examine, by Figure 4, the behavior of samples of different shapes according to water transfers.
We compare the state of the drying process with samples of different shapes undergoing the same drying conditions. These samples have similar sizes in order to avoid the influence of the size parameter, or form factor.
Thus, samples of cubic shapes 1 cm of edges, spherical of diameter 1 cm, cylindrical of diameter-height 1 cm × 1 cm have slightly different behaviors.
Likewise, the samples with the respective dimensions 2 cm edge, 2 cm × 2 cm in diameter-height and 2 cm in diameter behave with a slight behavior,
It is the same for the other dimensions, namely 3 cm, and 4 cm as an order of magnitude as a dimension
In short, if we set the size parameter, samples of different shape have a similar behavior, with a slight advantage for the cube, which has the lowest resistance to mass transfer. This difference is of the order of 0.1 kg/Kg of water content between the cube and the spherical shape obtained after 250 min of drying time, for the dimensions of 2 cm
Between the cylindrical and spherical shape, the cylindrical shape has a drying advantage. The maximum difference observed is of the order of 0.01 kg/kg of water obtained after 150 min of drying time, for dimensions of 1 cm.
4. Conclusions
The results obtained during the convective drying of samples of potatoes of various sizes and shapes reveal the importance of taking these dimensions into account during their drying.
For the different shapes used, the results show that the small samples are less resistant to water transfer during drying. For the cubic form, a 50% decrease in water content was obtained after 50 minutes of drying for the dimension of 1 cm against, 10% decrease in its water content of the sample at 4 cm of edge. The difference is therefore 40%.
Similar results were obtained for the other forms thus confirming the importance of the role of size in the evaluation of the drying of organic products.
For this present work, which examines samples of different shapes but with similar dimensions, it appears that for the same characteristic dimension, shape does not seem to be an important parameter. Thus, cubic, spherical or cylindrical samples dry almost identically if they have the same characteristic dimension: edge for the cube, diameter for the sphere and height-diameter for the cylinder shape.
To complete this study, we would like to take into account several forms at various drying temperatures in order to better identify the role that size plays on transfers. Also, by examining the characteristic dimensions defined by Ouoba (2013) [13], we will therefore be able to better take into account these aspects of form for our next work.
We recommend that the dryers cross the temperature, shape and size parameters for optimal results of the dried product.
It would also be more advantageous to keep the dimensions as small as possible. It would be more judicious to have a low thickness, before any process of drying agrifood products.