Sedimentological Studies of Alluvium Deposits along Ngovayang-Bipindi of Lokoundje River, Southwestern Cameroon ()
1. Introduction
The study area is located in the coastal plain of Cameroon. The coastal plain is the lowest elevation zone (0 - 350 m), [1] [2] see in this plain a succession of three levels of increasing altitude from the sea to the southern plateau of Cameroon. This study is conducted with the aim of knowing the sedimentological characteristics of a coastal plain zone, which is favorable to the accumulation of the erosion materials rich in useful substances; just because it is located below a mountain range where weathering is important and the outcrops are rare because of the forest. The Ngovayang Mountain, which constitutes a dense intrusive rock [3] according to some prospecting activities, would potentially be rich in useful minerals. This region is also drained by a very dense hydrographic network whose waters would facilitate the transport of materials. The importance of alluvium is no longer to be demonstrated in terms of the quintessential mineral exploration site when indices are reported in a region. The case of Bétaré-Oya in the eastern Cameroon region can well illustrate it. There, many mining companies explore and exploit gold in placers, where one of which is just located below hills in Mali village. Numerous petro-structural and metallogenic studies have been conducted in the Lower Nyong region including Ngovayang, which has been strongly influenced by the eburnean orogeny. It appears that the Nyong unit, in general, contains relics of the TTG (Tonalite-trondhjemite-granodiorite) series, various intrusive rocks, and greenstone belts, all strongly affected by the eburnean orogeny around 2050 Ma, and intersected by dolerites [4] [5] [6]. In the same way, these results confirmed the presence of platinoids and minerals present on ultrabasic rocks. However, there is no real previous sedimentological study in the area. We have volunteered to start a study whose general objective is to know the sedimentological characteristics of the alluvium deposits of Lokoundjé River and its tributaries in the vicinity of Bipindi; deduce sediment deposition environment and associated sediment dynamism; identify relevant indicators that can reveal the origin of the minerals found; establish an evaluative draft of social and environmental impact in the context of a future alluvial mining operation. The expected results are to find mineralization indices in the area, which would be useful for mining exploration of gold and related minerals. Mining in the county is at an embryonic stage. Mining companies are currently exploring uranium, gold and iron in the area. In addition, sand quarries are exploited on the banks of the Lokoundjé River and on some of its tributaries Tyango and Nsola.
2. Natural Environment and Geological Setting
2.1. Natural Environment
The study area is located in the coastal plain region of Cameroon (Figure 1). The coastal plain is the lowest elevation zone (0 - 350 m), [1] [2] see in this plain a succession of three levels of increasing altitude from the sea to the southern plateau of Cameroon. However, the observation of the topographic map of Edea at the scale of 1:50,000 subdivide the study area into four geomorphological units where high altitudes represent the peaks of the Ngovayang mountain range (Figure 2). The climate of the zone is equatorial Guinean type with four seasons. The average minimal temperatures are in the region of 23.4˚C, with 32.5˚C as monthly maxima [7]. The study area is dominated by evergreen forest with large buttressed and rooted trees (Figure 6) such as Microberlinia bisulcata and Piptadeniastrum africanum [8]. This forest is subject to strong anthropization. It is characterized by an abundance of rotang, raphial species; aquatic ferns and algae
Figure 1. Location map of the Ngovayang area at Bipindi, southern Cameroon.
Figure 2. Geomorphological map of the study area extracted from the Edéa topographic map.
in marshy areas. Chinese bamboos are in hydromorphic soils. The hydrographic network of the study area is dense in lattices with a rectangular tendency. It is part of the Lokoundjé watershed, the main collector of the region. Its rivers are organized in a network of order four (Figure 4). Its watershed covers an area of 5200 km2 with a perimeter of 331.6 km [9]. The Lokoundjé River takes its source in the southern plateau of Cameroon and travels 216 km to the sea with a direction of flow ENE-WSW. In the same order, we find that all streams flow between fractures and are almost all affected by structural guidance. There are two main types of soils, based on the synthesis of soil studies in southern Cameroon [10] [11] [12] [13] [14]. We distinguish from this fact ferrallitic red and yellow soils on interfluves and hydromorphic soils in the lowlands.
2.2. Geological Setting
The complex is made up of three units namely: Ayina unit, Ntem Unit and the Nyong unit. The study area belongs to the lower Nyong unit of the Ntem group correspond to the remobilized northwestern border of the Congo Craton (CC) in southern Cameroon. The Lower Nyong unit consists of Archean and Paleoproterozoic rocks with tonalite-trondhjemite-granodiorite (TTG), dolerites, alkaline syenites, greenstone belts (epidotites, serpentinites), orthopyroxene?garnet gneisses (charnockites), garnet-amphibole-pyroxenites, biotite horn-blende gneisses, and BIFs [15] [16]. The region is affected by the eburnian orogeny 2 Ga years ago [4]. The Nyong Unit consists mostly of metasedimentary, meta-volcanic and intrusive rocks. Palaeoproterozoic rocks are ortho amphibolites (Figure 3), iron formations and intrusive granitoids alternating with various gneisses [17]. The zone underwent three deformations characterized by foliations, schistosities, folds, shears, recesses, joints, flanges, lineations and tension slits. According to the
Figure 3. Geological map of SW Cameroon (modified after [17] ) showing the Kpwa-Atog Boga area related to the Ngovayang massifs in [23].
work done by [17] - [22]. The dolerites, the peridotites and the gabbros are exposed in the form of veins intersecting the structure of the preceding rocks [5].
The study area is composed of the rocks from the greenstone belt. Firstly they are Ortho and para-metamorphic rocks that are generally leucocratic gneisses, amphibolic gneisses and calcium gneisses (Figure 3). They are generally in the form of balls on firm ground and in slabs at the level of the rivers or in banks near. Secondly they are Magmatic rocks that are generally syenites, pyroxeno-amphibolites, iron formations and basic and ultrabasic rock veins. It shows that, the Lower Nyong unit has been altered during geological time because of numerous climatic changes on the one hand, and on the other hand this alteration is favored by the nature of the rocks called ultrabasics and their tectono-metamorphic evolution. Ultrabasics are rocks that rapidly deteriorate because of their high percentage of ferromagnesis, hence an interest for mining exploration in recent sedimentary deposits.
3. Methodology
The methodology of work is divided into two major activities including field campaigns and laboratory work. The fieldwork consists of recognition and delimitation of the sector to be studied using map 1/200,000 of Edéa NA-32-XXIII; the choice of sampling sites (Figure 4) and their geographical location (Table 1). Sample collection was done in holes. Their depth varies from one to one and a half meters, depending on the appearance of water (Figure 5, Figure 6). Where, we collected one to three samples per hole from the base upwards. In laboratory, sand samples are subjected to sedimentological analyzes namely the granulometry, morphoscopy of quartz grains, the study of heavy minerals and the morphometry of pebbles.
The granulometric technique makes possible to establish a precise textural description of the sediment and to understand the active mechanisms during the transport and the deposition of the particles. The samples, after drying in an oven at 108˚C for 24 hours, are subjected to successive quartering until 200 g of material are obtained in each sample. Then the 200g are tap washed in a 50 micron sieve to remove fine particles, then dried and weighed. At the end the sediment is passed through a sieve column arranged in a decreasing manner (2 - 1.60 - 0.800 - 0.315 - 0.250 - 0.200 - 0.160 - 0.125 - 0.080 - 0.063 - 0.050 - <0.050 (mm)). The goal here is to determine the percentage of refusal on each sieve and weigh it.
Mi = (MR × 100)/MRC;
Mi: Relative frequency of the particles, MR: Refusal mass; MRC: Total mass of cumulated refusals.
Concerning the morphoscopy, on the mesh samples of: 1.250 - 0.800 mm; 0.8 - 0.315 mm and 0.315 - 0.200 mn, we randomly take and count 100 grains of quartz per sample for the observation by binocular magnifying glass to inspect the state of the surface, the shape of the quartz grains per sample. It consists in
Figure 4. Sampling points map and Hydrographic map of the study area extracted from topographic map 2A at 1/50,000.
Table 1. Geographical coordinates of sampling sites.
Figure 5. Plate log of different holes samples collection.
determining the mode and the duration of transport of the grains, thus making it possible to reconstruct the geological history of the latter.
Heavy minerals are minerals with a density greater than 2.89. Their study consists in knowing the nature of the rock they come from on the one hand and on the other hand to specify their distributing province. Preparation techniques are those recommended by [24] [25].
Pebbles for morphometry study are aggregates used to apprehend transport agents and to evaluate the wear process of these materials. This indicates that the forms observed depend simultaneously on the hardness of the original materials, as well as the mode and duration of transport [26]. According to [27] it is necessary to take 50 pebbles and examine each of them using a caliper (Figure 7).
Calculate from this fact:
The flattening index A = L + 1/2.e;
The blunt index I = 2r.l. 1000/L;
The dissymmetry index D = 1000. AC/L.
4. Results
4.1. Granulometry
The histograms relate to Wentworth’s classification of the diameters (d) of the sand grains. We obtained sixteen (16) histograms of which four are represented here (Figure 8).
The histograms of the 16 samples presented two modes respectively in classes 0.800 mm - 0.315 mm and 0.200 mm - 0.160 mm; with the exception of the histograms of samples Mou1a and Nso1a. The major parts of the dominant particles have a diameter between 0.315 mm - 0.080 mm.
Cumulative curves
In the same way as for histograms, we plotted on the abscissa the diameters of the meshes on a logarithmic scale and on the ordinate the cumulative percentages in mass of rejections expressed on an arithmetic scale. In order to have reliable results of the sediment deposition mode, the coarsest ones that are deposited first, and ends after [28]. Retrograde accumulation is used to show coarsest
Figure 7. Morphometry of a pebble (modified after [27] ).
Figure 8. Histograms from the different sites of samples.
elements to the finest elements. The quartiles defined for this purpose are used to determine the granulometric parameters such as the Krumbein Qdphi or quartile of deviation. It is a ranking index that allows assessing the extent of sorting actions during transport and sediment deposition. It also makes it possible to determine whether the sediment is better sorted, especially as its value will approach zero.
Qdphi = (Q1 × Q3)/2
Qdphi: Quartile of deviation.
The Sorting Index (S0 = (Q1/Q3) 1/2) is an index whose limits are proposed by [29] , and which gives information on the type of filing classification. The consequences are as follows:
S0 < 1.23; very high grade (sediment very well classified);
1.23 < SO < 1.41; good grade (well classified);
1.41 < S0 < 1.74; medium grade (averagely classified);
1.74 < S0 < 2.00; poor classification (poorly classified);
S0 > 2.00: very poor grade.
Coefficient of Asymmetry
Asymmetry provides more information on the depositional environment than transport conditions [26]. It expresses the distribution of the elements with respect to the median Q2, and is expressed according to the formula:
A = (Q1 × Q3)/Q22
The limits of this coefficient imply the following consequences.
A < 1: Classification is done on the side of coarse elements. Asymmetry is said to be negative and results in the elimination of the finest fractions either by high turbidity, it is most often torrential.
A > 1: The classification is made towards the finer elements, the asymmetry is said to be positive. These are deposits characterizing the basin bottoms.
A = 1: The mode of the curve coincides with the median or average diameter (these are sediments called little evolved.
The results of the various calculations of the sedimentological indices (Qdphi, S0, As) are recorded in the table (Table 2).
The curves of the cumulative percentages of the samples show a fairly steep slope. The granulometric parameters are generally those of very well classified sediment, very well sorted and of negative asymmetry. In this assumption from granulometric study, the majority of histograms show a unimodal particle size appearance. This indicates that there is a single source of sediment. Moreover, the observed bimodality in Mou1a and Nso1b samples suggests that the sediments are derived from more than one source. The deposit methods are formed
Table 2. Summary of the various granulometric parameters calculated.
by traction, saltation and suspension (Figure 9).
4.2. Morphoscopy
The grains observed are classified into several types: the unworn, the blunted shape and the glowing sub-blunt shape. The different results obtained following observations of quartz grain surfaces with a binocular magnifying glass are shown as follows (Table 3).
The morphoscopy shows that the grains have more than 80% at an angular
Figure 9. Cumulative curves showing well sorted and classified sand grain at all the sites.
Table 3. Counting results of the surface aspects of quartz grains and their average percentage.
NG: Number of quartz grain, NW: Non Worn, SBS: Sub Blunt and Shiny, BS: Blunt and Shiny.
appearance (Figure 10). Dirty or yellowish color is observed in some grains but in a negligible volume. It is the successful outcome of the presence of iron oxides. Lokoundjé the main collector with a length of 216 km cannot quite polish the surface of the sand grains as the necessary distance is approximately 300 km. So the source of sediment is more or less proximal. This is somehow evidence of a fluvial environment where the grain of sand from tributaries and hazards suffered by the Lokoundjé. This hypothesis is supported by the presence of metal oxides that permeate or cover some sand grains. This is evidence of weathering in forested areas, where sediments are not easily transported in the calm waters. The second category consists of sub-rounded grains. It represents 19% of the grains of sand. These are major part of medium to coarse sands. Grains have shapes or contours bad cut. Some grains, like angular present piecemeal metal film reddish color. We can say that these grains are from a more or less distal source and are subject to fluvial transport. The third category is worn grain, it is the least represented. Moreover, these grains could come from a more or less distal source, but in flood conditions where grains would clash and wear out. The presence of non-round grains mats indicates the absence of a wind transport can be explained by the thick forest cover in the region. In view of this, we will remember that the presence of angular grains is more influent than the Lokoundjé. However, sub-rounded covered with a deposit of fluvial environment or deposit river low energy. The absence of the mat round type characterizes
fluvial transport forest.
4.3. Heavy Minerals
Heavy minerals are minerals with a higher density than bromoform (2.89). These are most often ferromagnesian minerals, metamorphic silicates, titaniferous minerals and accessories. They are most often said to be economical and profitable or interesting.
In the study there is a high content of zircon (Figure 11) and garnet. The other minerals are on the order of two to three percent on average (Table 4). In addition we have enough of opaque oxides which are most often iron minerals, that is to say more than 50% of the total volume of minerals.
Garnet and mafic
Garnet is abundant. It is colorless in natural light and off in polarized light. He cracked the terrain very strong, with inclusions of quartz. It is a mineral of general metamorphism of low to medium pressure and medium temperature. Its average content is estimated at about 13%. The green hornblende is observed in samples Mou1a, Tya1b. It occurs as short fragments or lying prism. The green to
Figure 11. Plate showing heavy minerals from sands (Optical microscope).
Table 4. Inventory of heavy minerals in the presence.
dark green NAPL, it also has shades of the second order. Its pleochroism is visible with oblique extinction. It represents less than 5% in these samples. The tourmaline is found in all samples prismatic. It is yellowish in color and light yellow in NAPL LPA. Its relief is moderate and represents 2%. The biotite is observed only in the sample Nso1b, yellowish to reddish brown in polarized light. It is being chlorite and is estimated at about 2%.
Silicates metamorphism
They are formed under conditions of medium to high pressure and medium temperature. The andalusite is rare, and is found in Mou1b and Tya samples. It is colorless to pale pink, medium terrain. Comes in the form of angular grains, it polarizes in vivid hues of the second order and represents about 1% in these samples. The kyanite is observed in samples Tya1b Mou1b and it is colorless NAPL blue to pale blue LPA. It is usually in the form of elongated tablets. Its divisions are orthogonal and an estimated 2% content. Sillimanite occurs with prism-shaped serrations or fibers. It is found in most of the concentrates. It is colorless and clear in strong relief. The Sillimanite polarized in purplish red hues of the first order and represents an average of 3%.
Titaniferous minerals
The Sphene is present in Mou1b and Nso1b samples. It is colorless and greenish blue in natural light LPA. Its terrain is very uncommon with pleochroism. It has an oblique extinction in polarized gray tint of the first order, it is highly birefringent, and its content is estimated at 2%.
The accessory minerals
Apatite is present in the sample Tya1a, colorless to light polarized dark gray PCPA its extinction is right. Monazite is present in the sample Lok1; it has a yellowish brown to orange-green. It is split and has a shiny glaze. We estimate that less than one percent of the volume of the rock. The topaz is also estimated at less than one percent. It has a prismatic colorless color tone blue with a glassy appearance NAPL. We watched in Lok1 and Soft samples.
Opaque oxides
Opaque oxides are present in all samples collected sites. They represent on average 40% of the sample volume of thin sections. They come in different shapes and are visible only in polarized light (Figure 11). In sum, the study shows that the source of sediment is of magmatic and metamorphic origin respectively with minerals such as hornblende, zircon, tourmaline and other minerals such as kyanite and sillimanite.
4.4. Morphometrical Study of Pebbles
The study concerns pebbles essentially collected in the Tyango’s tributary alluvium. The alluviums of the other tributaries including those of Lokoundjé River do not have pebbles. The results obtained after studies are also recorded in the table below.
The informations collected on studies of pebble Tyango River (Table 5) indicate that the flattening index, show unimodal curves. So, shows that the source is unique, pebbles are relatively flat and more than 50% have sub-spherical shape.
Table 5. Distribution of different morphometric index measurements of pebbles.
The blunt index gives information on the situation of the source. In this case, the shape of the curve is bimodal and is sub-blunt roller. This is evidence of a more or less short transportation. The Assymetrical index gives evidence that the pebbles are different from a sphere, because nearly 80% of pebbles collected exhibit disphérique form. We may retain in light of all this information, the rollers of the river are Tyango proximal origin have undergone short transportation. They are slightly worn and disphériques.
5. Discussion
5.1. Depositional Set up
Bipindi area is dominated by the southwestern tip of the Ngovayang, altitude of 1090 m. It is a vast plain that extends to the Atlantic Ocean which is located at about 70 km. This potentially mining area is subject to an Equatorial Guinean climate. Significant rainfall promotes the erosion of materials, which are kidding from the hillsides of Ngovayang Mountain to Lokoundjé River and its tributaries located below. The dip of approximately 5˚ to the west of oblique stratifications indicates that the deposits describe a monoclinal structure where an accumulation of continental and meteoric iron occurs. This is all the more confirmed by the unstirred place, with the result of a good grading and sorting of grains.
With respect to the deposit environment of alluvial, geodynamic reveals many variations on rock types. Moreover, they are the consequence of the variations of the conditions of the environment. The sands in the course of the study are fine and coarse as well. We stipulate that this is a result of hot period, while keeping in mind that it is in fluvial channels where there are many leaching elements. Nevertheless, we can use the color and thickness criteria of the facies to better decipher the depositional periods. Thus the small oblique stratification corresponds to the periods of flooding, whereas the thick stratifications correspond to the periods of low water.
5.2. Mining Interest
In view of all studies carried out including the geomorphology aspect of the environment, we do believe that the southwestern sector of the Ngovayang-Eséka range in Bipindi has the characteristics of a beneficial minerals accumulation. Then by taking into account the age of the materials, the alluvial deposits are all repositories. However, at the regional scale, the majority of fluvial placers date from Cenozoic [30] [31] ; this is the case in the area with Precambrian basement rocks, Eburnean age.
According the tonnage and the content, the information obtained from the work on the site of panning of Jules Amenguelé in Abiété Yenjok located to about thirty kilometers in the south. The result content show: 0.35 g/m3 and 1.22 g/m3 Au. According to [32] the high tonnage is 0.1 to 100 Mt with low levels from 0.05 to 0.25 g/T Au and 50 - 200 g/T in Sn. Moreover, a minimum level for a profitable operation is 0.1 g/m3 [33] ; which is far below the levels observed in our region. In addition, in the observation of heavy minerals, we have more than 50% opaque oxides which are relevant indicators for the presence of useful minerals, as it is the case with placers elsewhere. These minerals are the following: Diamond, platinum, zircon, sapphire, tin, titanium, chromite and many others. In addition, sedimentological studies confirm a short transport of sediments that is unfavorable to the dilution of particles with mechanical transport by water. Thus, the useful minerals at best will be found in their primary form. This idea is supported by the discovery one year ago, of gold in alluvial deposits upstream, in the north of the Ngovayang-Eseka range. Currently this is subject to exploitation by mining artisans in the town of Eseka.
In short, economic ores are concentrated by gravity, chemically resistant to weathering and durable. They include zircon, rutile, monazite and many others in the surrounding sediments during a long period. Thus the recent deposits are found in basin context, either in surface and sub-surface environments [33] where they can be influenced by climatic hazards and biological organisms. We retain that the Ngovayang-Eséka range, in a collisional context between the South Cameroon Plateau and the Congo's north Equatorial Craton, is the major provider of useful sediments and concentrations in our area; further investigations should be done to accurately evaluate the tonnage of different useful minerals.
6. Conclusion
17 samples of alluvial sands were collected in Lokoundjé and some of its affluent, for environmental and sedimentological study of alluvial deposits around Bipindi. From the coarse and fine grain size of these sands, three aspects of quartz sand grains emerge. The unworn and angular grains are dominant and show proximal origin sedimentation. Moreover, the absence of round grain matt reflects the absence of aeolian transport because of the forest cover. Pebbles collected in Tyango River are very little blunting, dissymmetrical and slightly flattened; they give evidence of a short haul. Heavy minerals consist of andalusite, zircon, monazite, biotite, green hornblende, zoisite and kyanite. They come from two vending areas, the plutonic and metamorphic formations. In term of economic mineralization, the conditions for setting up gold are good; some panning in the alluvium will be needed to attest it. Nevertheless we do already have discreet presence of topaz and monazite. Large amounts of zircon and garnet were also obtained. Detailed investigations should be carried out in geochemistry and petrography in order to elucidate the nature of the hidden minerals in the great quantity of opaque oxides or minerals.