Low-Spatial Coherence High-Power Electrically Injected 6xx nm Dual-Emitter Laser ()
1. Introduction
Laser-based displays have attracted much attention and a bright prospect, because the laser is the only light source that produces saturated primary colors that reach over 90% of what our eyes can see, in another word, big gamut [1] and the laser display can realize the larger screen. However, there still exist the drawbacks such as the speckle, a pattern formed by the interference of the laser owing to the high spatial coherence. The speckle pattern is considered as a negative factor in the laser display [2].During the years, different ways have been presented to reduce the speckle pattern. For instance, angle diversity, polarization diversity, wavelength diversity [3], rotating diffuser [4], and the Grating Light Valve (GLV) [3]. Goodman has proved that the speckle contrast C will be N−1/2 which N means the independent modes [5]. Nevertheless, the methods mentioned above achieve the low speckle contrast by averaging the speckle patterns in the external cavity. To decrease the speckle effect fundamentally, we have to realize the low-spatial coherence of the light source.
There are some ways to suppress the speckle by reducing the spatial coherence of the laser such as the random laser that can tune the spatial coherence by varying the density of the scatters [6], degenerate cavity which can obtain the many transverse modes to reduce the spatial coherence [7]. However, the random laser and degenerate cavity cannot realize the electrical injection and the compact size. In order to realize the commercialization, there are some conditions to satisfy for the device: electrically injection; high conversion efficiency and directionally emission beam [8]. We recently demonstrated that the electrically injected random lasing based on disordered photonic crystal structures [9] and the low-spatial coherence electrically injected red-emitting semiconductor laser [10].
In this paper, we will present latest results of new low-spatial coherence 6xx nm dual-emitter for relative high power. The maximal output power is 510 mW under 20˚C, pulsewidth of 40 μs and repetition frequency of 40 Hz after packaging. The speckle contrast is measured to be 5% in the same way in [11].
2. The Structure Design of Device
We use the coupled-cavity structure that consists the D-shaped cavity and the Fabry Perot (FP) cavity to obtain the multimode lasing simultaneously and relative high power output. The D-shaped cavity structure depends on the R, d and L which represent the radius of the D-shaped cavity, the distance between the flat edge and the center of the D-shaped cavity and FP cavity length respectively. Figure 1 is the schematic structure of the dual-emitter laser. We simulated the mode distributions of different d at the wavelength of 630 nm and adopted d = 0.5R because of the uniform mode distribution while the other parameter like d = 0.8R showed the stable orbit in the D-shaped cavity. The former has more modes lasing simultaneously.
3. Device Fabrication
We adopted the R = 500 μm, d = 250 μm and L = 1000 μm to obtain the more lasing modes in order for low-spatial coherence. The fabrication process is relatively simple and low-cost. We used the standard photolithography and ICP to obtain the pattern of the cavity. The cleaved laser bars coated with 8% antireflection film to increase output power. Finally, the devices were mounted P-side up on Cu mounts.
4. Device Result
4.1. Power and Spectrum Measurement
First, the power-current curve is measured first to confirm the maximal power the dual-emitter can reach under 20˚C, pulsewidth of 40 μs and repetition frequency of 40 Hz. The power of the dual-emitter laser emitted exceeds 500 mW while the single emitter emits 300 mW. Then we measure the spectrum of the dual-emitter laser at different currents under the same pulse condition. Figure 2 is the spectrum and spectrum width at full-width-at-half-maximum (FWHM). There is an obvious narrowing for spectrum width when the current exceeds the threshold value. It proves the dual-emitter become lasing further.
Figure 1. Schematic of the dual-emitter laser.
Figure 2. Schematic of the emission spectrum and the spectrum width at FWHM collected from the dual-emitter laser at different currents.
4.2. Speckle Measurement
Next we characterized the spatial coherence of the dual-emitter laser. The speckle contrast C is introduced to characterize the spatial coherence of the laser. It is defined as:
. (1)
The
is the standard deviation of intensity and
is the average intensity. The speckle contrast is a value from 0 to 1. The low-spatial coherence equivalent to the low C which means the less influence on the image quality. However, there is still no standard method to measure the speckle [12]. We make a comparison between the dual-emitter laser and the traditional broad area (BA) laser in speckle contrast and image quality. It is similar to the method in [11]. Figure 3 shows the setup of speckle measurement. Figure 4 is the speckle pattern collected from the traditional laser and the dual-emitter laser. We can clearly see the speckle patterns collected from the BA laser and the dual-emitter laser. The speckle contrast of the BA laser is 0.11 while the dual-emitter laser is 0.05. It means the dual-emitter laser has the lower spatial coherence.
5. Conclusion
For the fabrication of the dual-emitter laser, it only needs the standard photolithography and ICP etching process. It shows the low-spatial coherence which
Figure 3. The speckle measurement setup.
Figure 4. (a) The speckle pattern collected from the BA laser and (b) the dual-emitter laser.
the speckle contrast is 5%. The relatively power exceeds 500 mW is obtained under 15A pulse condition (40 μs 40 Hz). It has a bright prospect as a low-spatial coherence light source in the laser display.
Acknowledgements
This work was supported by the National Key R & D Program of China (2016YFB0401804 and 2016YFB0402003).